Commercial or technical designation of a manufacturer's product family sharing a common design and compatible characteristics.

Range of tasks and systems for which the manufacturer recommends the component.

Primary function of the device and its intended use as defined by its design and the manufacturer's documentation.

Permissible installation location of the product: indoors, outdoors, in a technical area, or as part of equipment.

Environmental conditions under which installation and operation of the product are permitted.

Permissible spatial orientation of the component during installation and operation.

Number of structurally separated sections forming the enclosure or distribution board.

Number of internal compartments separating the functional zones of the equipment.

External horizontal dimension of the product between its outermost lateral points.

External vertical dimension of the product from its lowest to its highest point.

External distance between the foremost and rearmost surfaces of the product.

External linear dimension of the product along its longitudinal direction or principal length axis.

Dimension of a material, part, or product between two opposite surfaces, measured in the thickness direction.

Available distance between the internal side surfaces of the enclosure.

Available distance between the internal top and bottom surfaces of the enclosure.

Available distance between the internal front and rear surfaces of the enclosure.

Portion of the internal width actually available for positioning and mounting equipment.

Portion of the internal height actually available for positioning and mounting equipment.

Portion of the internal depth available for equipment, taking into account the door, panels, and cabling.

Distance between the internal and external surfaces of the main enclosure wall.

Distance between the internal and external surfaces of the rear wall of the enclosure or component.

Overall thickness of the door leaf, excluding protruding handles and door-mounted components.

Horizontal dimension of the door leaf between its outermost lateral points.

Vertical dimension of the door leaf between its lowest and highest points.

External horizontal dimension of the mounting plate between its outermost side edges.

External vertical dimension of the mounting plate between its bottom and top edges.

Distance between the opposite surfaces of the mounting plate defining its thickness.

Horizontal dimension of the mounting cutout or opening required to install the product in a prepared surface or recess.

Vertical dimension of the mounting cutout or opening required to install the product in a prepared surface or recess.

Depth of the mounting cutout or recess intended to accommodate the recessed part of the product.

Depth of the enclosure portion installed within a wall or mounting recess.

Distance by which the front part of the installed product projects beyond the wall surface.

Actual clear width of the open passage, excluding frames, edges, and protruding components.

Actual clear height of the open passage, excluding frames, edges, and protruding components.

External horizontal dimension of the frame between its outermost lateral points.

Vertical dimension of the plinth from its supporting plane to its upper edge.

Mass of the product itself, excluding transport packaging, additional accessories, and external equipment.

Total number of standard DIN modules that the product is designed to accommodate.

Number of mounting rows provided for installation of equipment.

Number of standard DIN modules that can be accommodated in a single mounting row.

Number of DIN rails provided for mounting modular devices or other compatible equipment.

Number of standard DIN modules that can be accommodated on a single DIN rail.

Total longitudinal length of the DIN rail available for mounting equipment.

Nominal pitch of one DIN module used to determine the width and mounting capacity of modular equipment.

Profile type of the DIN rail installed in the product or specified for compatible mounting.

Spatial orientation of the DIN rail relative to the product in its intended installed position.

Vertical distance between corresponding mounting lines of adjacent DIN rails.

Horizontal distance between corresponding mounting lines of adjacent DIN rails.

Indicates whether the DIN rail position can be adjusted in depth relative to its standard mounting position.

Range of DIN rail movement in the depth direction where adjustment is provided by design.

Number of separate vertical columns or mounting zones provided by the product design.

Number of mounting rows located within one structural section.

Total number of standard DIN modules that can be accommodated within one structural section.

Number of separate installation fields provided for equipment or functional components.

Number of separate fields intended for installation of electrical devices and equipment.

Number of positions provided by design for installation of metering devices or meters.

Number of separate mounting fields intended for multimedia, telecommunications, or extra-low-voltage equipment.

Number of separate fields intended for control and automation equipment.

Number of separate fields intended for busbar systems and associated components.

Number of separate fields intended for cable entry, routing, distribution, or connection.

Number of separate fields intended for terminals and other conductor connection components.

Number of separate mounting plates provided by the product design.

Number of separate mounting levels or planes provided for installation of equipment.

Number of internal supporting or mounting frames provided by the product design.

Number of internal mounting chassis intended for fixing equipment and structural components.

Number of structurally separated functional units performing independent functions within the product.

Maximum external width of an individual device permitted for installation within the designated mounting space.

Maximum external height of an individual device permitted for installation within the designated mounting space.

Maximum external depth of an individual device permitted for installation within the designated mounting space.

Primary material from which the walls and load-bearing part of the product enclosure are made.

Grade, class, or technical designation of the enclosure material specifying its composition and properties.

Primary material from which the product door is made.

Grade, class, or technical designation of the door material specifying its composition and properties.

Material of the transparent or inspection part of a window installed in the product door, cover, or enclosure.

Primary material from which the mounting plate used for securing equipment is made.

Grade, class, or technical designation of the mounting plate material specifying its composition and properties.

Primary material from which the supporting or mounting frame of the product is made.

Grade, class, or technical designation of the frame material specifying its composition and properties.

Primary material from which the product plinth or base is made.

Material of sealing elements used to seal joints, doors, covers, or entries.

Primary material from which the product door or cover hinges are made.

Primary material of the housing and mechanical parts of the product lock or locking device.

Primary material of screws, bolts, nuts, rivets, and other product fasteners.

Primary visually perceived colour of the product's external surface.

Designation of the product's primary surface colour according to the RAL colour system.

Primary visually perceived colour of the external surface of the product door.

Designation of the product door colour according to the RAL colour system.

Primary visually perceived colour of the mounting plate surface.

Designation of the mounting plate colour according to the RAL colour system.

Type of final surface finish of the product determining its appearance and service properties.

Type of final door surface finish determining its appearance and service properties.

Type of final mounting plate surface finish determining its appearance and service properties.

Character of the surface microrelief and visual structure after manufacturing or finishing.

Technological surface treatment applied to modify its protective, mechanical, or decorative properties.

Type of protective, functional, or decorative coating applied to the surface.

Material or chemical basis of the coating applied to the surface of the product or one of its parts.

Thickness of the coating layer applied to the surface of the product or one of its parts.

Type of powder coating defined by the material system used or the technology employed to form the protective layer.

Type of final mechanical or chemical surface treatment applied to a stainless-steel part.

Indicates whether the door is fully or partially transparent, allowing visual inspection of the internal space.

Degree or category of optical transparency of the inspection window material.

Indicates whether the product material has properties that reduce its ability to ignite and propagate flame.

Indicates whether the product material is classified as halogen-free according to the characteristics declared by the manufacturer.

Indicates whether the product's primary material has electrical insulating properties and is intended to electrically separate conductive parts.

Indicates whether the material has properties that limit the accumulation of electrostatic charge on the surface.

Indicates whether the absence of silicone has been declared for materials or process substances associated with the product.

Indicates whether the product's primary material is recyclable within the waste streams intended for it.

Proportion of recycled-origin material in the product or the relevant part.

Installation arrangement permitted by the product design, such as wall-mounted, flush-mounted, floor-mounted, or another specified mounting type.

Method used to mechanically secure the product to a support, surface, or load-bearing structure.

Type of surface or supporting base to which the product may be fixed.

Number of holes provided in the product for mechanical fixing.

Diameter of the hole provided for a fixing element used when mounting the product.

Geometric shape of the hole intended for mechanical fixing of the product.

Distance between the centres of mounting holes in the horizontal direction.

Distance between the centres of mounting holes in the vertical direction.

Horizontal dimension of the mounting pattern between the outermost fixing points of the product.

Vertical dimension of the mounting pattern between the outermost fixing points of the product.

Size designation of the screw, bolt, or other threaded fastener used for mounting the product.

Designation of the thread provided in the product's mounting holes or fixing elements.

Tightening torque recommended or permitted for fasteners during product installation.

Indicates whether the required fasteners are included with the product.

Type of anchors compatible with the specified product fixing method.

Number of anchors provided or required for standard product fixing.

Size or designation of the anchor specified for product installation.

Indicates whether wall brackets are included with the product.

Design type of wall bracket used to secure the product.

Number of wall brackets provided for product installation.

Indicates whether the wall brackets allow adjustment of the product position after installation.

Distance between the rear surface of the installed product and the mounting wall or supporting surface.

Indicates whether the manufacturer requires the product to be mechanically fixed to the floor or supporting base.

Number of holes in the product base intended for anchoring it to the floor.

Nominal diameter of a hole in the product base intended for installation of a floor anchor.

Horizontal distance between the centres of corresponding floor anchoring points along the X axis.

Plan-view distance between the centres of corresponding floor anchoring points along the Y axis.

Indicates whether adjustable or supporting feet for levelling the product are included in the standard supply.

Indicates whether the height of the support feet can be adjusted to level the installed product.

Full range of support-height or product-position adjustment available for levelling.

Indicates whether a plinth is required as part of the mounting system for standard installation of the product.

Indicates whether a plinth is included in the product's standard supply.

Method of mechanically fixing the plinth to the product, base, or other elements of the mounting system.

Indicates whether a mounting plate is included with the product.

Indicates whether the position of the mounting plate inside the product can be adjusted.

Full range of mounting plate movement in the depth direction where adjustment is provided.

Number of points by which the mounting plate is fixed to the product's supporting structure.

Maximum mass of equipment permitted to be installed on the mounting plate.

Indicates whether the design provides for mounting equipment on a DIN rail.

Indicates whether equipment may be mounted directly to the mounting surface without an intermediate DIN rail.

Mechanical rack-mounting standard to which the product or its designated mounting space conforms.

Number of standard rack units U available for compatible equipment.

Working depth of the space or fixing system available for installing equipment in a rack.

Minimum diameter of a cylindrical support on which the product may be mounted using the specified fixing method.

Maximum diameter of a cylindrical support on which the product may be mounted using the specified fixing method.

Indicates whether a clamp or similar fixing element for pole mounting is included with the product.

Indicates whether the design allows multiple products to be combined into a composite mounting system.

Indicates whether multiple products can be mechanically coupled side by side.

Indicates whether multiple products can be vertically coupled one above another.

Indicates whether the product supports functional or structural expansion using compatible additional modules.

Indicates whether a separate coupling kit is required to join the products.

Indicates whether the coupling kit is included with the product.

Minimum free space required above the product for installation, cooling, or servicing.

Minimum free space required below the product for installation, cooling, or servicing.

Minimum free space required to the left of the product for installation or servicing.

Minimum free space required to the right of the product for installation or servicing.

Minimum free space required in front of the product for installation and normal operation.

Minimum free space required behind the product for installation and normal operation.

Minimum free space in front of the product required for safe access during servicing.

Indicates whether the product can be installed using vibration isolators or other anti-vibration elements.

Indicates whether vibration isolators or anti-vibration mounts are included in the standard supply.

Indicates whether the manufacturer provides a mounting method for operation under declared seismic loads.

Indicates whether the product design permits suspended mounting to a supporting structure.

Maximum angle permitted by the manufacturer by which the product may deviate from the specified reference orientation during installation.

Maximum mechanical load permitted for the mounting system or fixing points under the declared installation conditions.

Number of separate doors provided by the product design.

Arrangement and combination of the product doors, including their number and relative positions.

Design type of door used in the product.

Direction in which the door moves when opening relative to the front of the product.

Side of the door or cover on which the main hinges are located.

Location of the hinges relative to the product door, cover, or enclosure.

Design type of hinges used to provide a movable connection between the door or cover and the enclosure.

Number of hinges supporting the product door or hinged cover.

Indicates whether the hinges allow the door or cover to be removed without destroying the connection.

Indicates whether the hinges are located inside the structure and concealed when the door is closed.

Indicates whether the design allows the door handing and opening direction to be reversed.

Indicates whether the door can be removed from the product for installation, servicing, or replacement.

Maximum angle between the closed and fully open positions of the door.

Indicates whether a device limiting the maximum door opening angle is included with the product.

Indicates whether a device that holds the door in the open position is included with the product.

Indicates whether a device preventing unintended door movement is included with the product.

Indicates whether a conductive door requires a separate protective connection to the equipotential bonding system.

Indicates whether a flexible protective bonding braid for the door is included with the product.

Design type of seal between the product door and enclosure.

Indicates whether the door seal is continuous around the entire specified perimeter.

Indicates whether the door has additional stiffening or structural reinforcement elements.

Indicates whether a supporting or mounting frame is provided on the inner side of the door.

Indicates whether a separate mounting plate can be installed on the inner side of the door.

Indicates whether electrical devices, controls, or indicators may be mounted directly on the door.

Maximum mass of equipment and accessories permitted to be mounted on the door.

Design type of handle used to open and close the door.

Indicates whether the door handle can be locked by a lock or locking mechanism.

Design type of lock used to restrict access to the product.

Operating principle or arrangement of the mechanism that locks the door, cover, or panel.

Number of separate points at which the locking mechanism secures the door or cover to the enclosure.

Number of independent locks installed or provided in the product.

Type or profile of key used for the product's standard lock.

Indicates whether a key for the installed lock is included with the product.

Number of keys supplied with the product.

Indicates whether multiple locks on the product or within the series can be opened with the same key.

Indicates whether individual locks have different key combinations and corresponding keys.

Indicates whether the locking system supports operation with a master key.

Indicates whether the locking mechanism accepts a compatible cylinder lock.

Indicates whether the product can be locked with a padlock.

Diameter of the hole or opening intended for the shackle of a padlock.

Indicates whether sealing is provided to reveal or control unauthorized opening.

Number of separate locations provided by design for applying seals.

Indicates whether the design makes opening or tampering with the established closure visually detectable.

Indicates whether a quarter-turn locking mechanism is used for closure.

Indicates whether a special key or tool is required to operate the locking mechanism.

Design type of cover that closes access to the interior of the product.

Indicates whether the cover can be completely removed for installation or servicing.

Indicates whether the cover is hinged to the enclosure and can be opened without complete removal.

Number of screws securing the cover in its normal closed position.

Indicates whether a tool is required to open or remove the product cover.

Indicates the presence of an additional inner door separating the accessible front area from equipment located behind it.

Indicates whether the inner door can be locked using the lock or locking mechanism provided by the design.

Indicates whether the inner door can be removed without irreversible alteration of the product.

Indicates whether internal components can be accessed from the front for operation or servicing.

Indicates whether internal components can be accessed from the rear for operation or servicing.

Indicates whether internal components can be accessed from the side for operation or servicing.

Indicates whether internal components can be accessed from the top for operation or servicing.

Indicates whether internal components can be accessed from the bottom for operation or servicing.

Number of removable or openable panels specifically intended to provide access to internal components.

Indicates the presence of an inspection window for visual observation of internal devices or indicators.

Indicates whether the inspection window or its leaf can be opened to access components behind it.

Indicates whether the inspection window can be locked using the provided lock or latch.

Indicates whether a pocket or holder for drawings, instructions, and other technical documentation is included.

Sides or areas of the product where the design provides for cable and conductor entry.

Design method used to route cables or conductors into the product.

Number of separate cable entries provided on the top side of the product.

Number of separate cable entries provided on the bottom side of the product.

Number of separate cable entries provided on the left side of the product.

Number of separate cable entries provided on the right side of the product.

Number of separate cable entries provided on the rear side of the product.

Number of separate cable entries provided on the front side of the product.

Number of removable or fixed plates intended for organizing cable entries.

Sides or areas of the product in which gland plates are installed or may be installed.

Design type of plate used to organize cable entries.

Material from which the plate used to organize cable entries is made.

External horizontal dimension of the gland plate.

External vertical dimension of the gland plate.

Distance between the two main surfaces of the gland plate.

Indicates whether the gland plate can be removed without damaging the product enclosure.

Indicates whether the gland plate can be replaced with another compatible plate.

Indicates whether the gland plate is supplied blank, without preformed holes.

Number of provided knockouts intended to be punched or broken out to form cable openings.

Sides or areas of the product in which knockouts for cable entry are located.

Geometric shape of the knockout that forms a cable opening when removed.

Nominal sizes of the provided knockouts or knockout openings.

Text designation of knockout sizes not represented by the standard dictionary options.

Minimum diameter of a circular opening obtained by removing the specified knockout.

Maximum diameter of a circular opening obtained by removing the specified knockout.

Indicates whether the design allows the opening to be reclosed after the knockout has been removed.

Number of finished holes intended for installation of cable glands.

Type of thread provided for installing or connecting a cable gland.

Nominal sizes of holes provided for cable gland installation.

Text designation of non-standard cable gland sizes or their mounting holes.

Minimum diameter of a hole provided for installation of a cable gland.

Maximum diameter of a hole provided for installation of a cable gland.

Indicates whether cable glands are included with the product.

Number of cable glands included with the product.

Material of the body or main part of the cable gland.

Number of flexible membrane entries provided for cables or conductors.

Nominal cable or opening sizes supported by the provided membrane entries.

Text designation of non-standard sizes of the provided membrane entries.

Material of the flexible membrane used in the cable entry.

Indicates whether the cable-entry membrane can be removed.

Indicates whether the membrane can re-establish the specified seal after a cable is inserted or removed.

Horizontal dimension of the enclosure area intended for cable entries.

Vertical dimension of the enclosure area intended for cable entries.

Dimension of the cable-entry area measured from the external surface toward the interior of the product.

Horizontal dimension of the clear opening intended for cable entry.

Vertical dimension of the clear opening intended for cable entry.

Minimum external diameter of a cable compatible with the specified entry system.

Maximum external diameter of a cable compatible with the specified entry system.

Maximum nominal cross-section of a cable or conductor permitted by the specified entry or connection.

Maximum external diameter of a cable bundle permitted by the specified entry system.

Indicates whether provision is made for mechanical strain relief of entered cables against tensile forces.

Indicates whether cable strain-relief elements are included with the product.

Indicates whether cable clamps or retainers are included with the product.

Number of cable clamps or retainers included with the product.

Indicates whether the product provides dedicated fixing points for cable ties.

Indicates whether the design permits separate routing of different cable groups.

Indicates whether separate routing of power and signal circuits is provided inside the product.

Type of system that seals the cable entry relative to the product enclosure.

Indicates whether a frame-based system is used to organize and seal cable entries.

Indicates whether a modular cable-entry system with replaceable or configurable elements is used.

Indicates whether split entries may be used for cables that cannot be passed through a one-piece seal.

Indicates whether the system permits entry of preterminated cables with connectors or terminations already fitted.

Indicates whether protection is provided against cable damage from sharp edges of the entry opening.

Indicates whether protective or sealing grommets for cable openings are included with the product.

Number of protective or sealing grommets included with the product.

Material of the protective or sealing grommet used in a cable opening.

Indicates whether a brush-strip entry is provided for routing cables through an opening.

Total longitudinal length of the brush element used in the cable entry.

Standard or interface size of the flange used for cable entry.

Number of flange interfaces provided for cable entry.

Indicates whether the material and design of the gland plate allow mounting holes to be drilled by the installer.

Number of unused cable entries reserved for future connections.

Type of electrical current for which the product's main supply circuit is intended.

Voltage value assigned to the product by the manufacturer for specified application conditions and characteristics.

Rated RMS value of alternating voltage assigned to the product by the manufacturer.

Rated direct voltage assigned to the product by the manufacturer.

Operating-circuit voltage with reference to which the product's performance characteristics are specified.

Maximum voltage at which continuous operation of the product is permitted under the conditions declared by the manufacturer.

Minimum voltage at which the manufacturer guarantees the intended operating mode of the product.

AC frequency assigned to the product for normal operating conditions.

Lower limit of the electrical network or signal frequency at which product operation is permitted.

Upper limit of the electrical network or signal frequency at which product operation is permitted.

Number of phases of the electrical system for which the product is designed to be connected or used.

Configuration of live and neutral conductors of the electrical system supported by the product.

Pole-count configurations for which the product is intended to be used or connected.

Rated external auxiliary supply voltage required for the product's active functions.

Type of current and source used for the product's auxiliary supply.

Voltage applied to the control circuit to perform the product's intended functions.

Type of current used in the product's control circuit.

Frequency of the alternating voltage or signal in the product's control circuit.

Current assigned to the product by the manufacturer for the declared operating and thermal conditions.

Highest rated current permitted for the relevant version or configuration of the product.

Rated continuous current for which the product's busbar system is designed.

Ratio of the permissible current-carrying capacity of the neutral conductor or busbar to the corresponding phase current capacity.

Factor accounting for the non-simultaneous loading of outgoing circuits when calculating the assembly.

Maximum rated current of a device permitted as the incoming device.

Maximum rated current of an individual device permitted in an outgoing circuit.

Maximum nominal conductor cross-section permitted at the product's incoming connection.

Maximum nominal conductor cross-section permitted at the product's outgoing connection.

Maximum nominal cross-section of the neutral conductor permitted by the relevant product connection.

Maximum nominal cross-section of the PE protective conductor permitted by the relevant product connection.

Conductor materials for which the specified terminals and connection methods are designed.

Conductor connection methods supported by the specified terminals or connection elements.

Tightening torque specified by the manufacturer for a screw or bolted terminal connection.

Voltage with reference to which the product's insulation clearances and dielectric properties are specified.

Peak value of an impulse voltage of specified waveform that the product insulation must withstand without breakdown.

Test voltage applied to verify the dielectric strength of the product insulation.

Minimum permissible insulation resistance between the specified electrically separated parts.

Category characterizing the expected level of impulse overvoltages at the product's point of use.

Degree of pollution of the surrounding microenvironment considered when selecting insulation distances and product characteristics.

Type of electrical insulation used, considered in terms of its protective function and construction.

Class of protection against electric shock determined by the product design and protective connection method.

RMS value of short-time withstand current Icw that the product can withstand for the declared duration without unacceptable damage.

Duration for which the product must withstand the declared short-time current.

Peak current value Ipk that the product can withstand under the declared short-circuit conditions.

Prospective short-circuit current that the product can withstand when the specified external protective device is used.

Manufacturer-declared permissible short-circuit current value for the product or assembly under specified conditions.

Maximum prospective short-circuit current at the installation point for which the product may be used.

RMS value of short-time short-circuit current that the busbar system can withstand.

Peak short-circuit current that the busbar system can withstand without unacceptable deformation or damage.

Indicates whether an external short-circuit protective device is required for the declared operation of the product.

Indicates whether an additional upstream protective device is required to achieve the declared product characteristics.

Indicates whether the design provides a point or means for connecting the product to the earthing system.

Indicates whether provisions are provided for protective equipotential bonding of conductive product parts.

Indicates whether a point or means is provided for protective bonding of a conductive door to the enclosure or PE system.

Indicates whether protective bonding of a conductive mounting plate to the enclosure or PE system is provided.

Indicates whether a dedicated point or terminal is provided for connection of the PE protective conductor.

Indicates whether a point or terminal is provided for connection of a combined PEN protective and neutral conductor.

Indicates whether a separate functional earth connection is provided that does not replace the PE protective connection.

Indicates whether the design permits the neutral busbar or conductor to be insulated from the enclosure.

Electrical network earthing systems with which the product may be used in the declared configuration.

Arrangement of the neutral conductor or neutral busbar within the product.

Indicates whether the neutral conductor can be disconnected for servicing or testing.

Indicates whether switching of the neutral conductor together with the live conductors is provided.

Indicates whether the product is equipped with an internal current-distribution busbar system.

Design type of busbar system used for electrical current distribution.

Material from which the current-carrying busbars are made.

Cross-sectional area of the current-carrying busbar.

Distance between corresponding axes or surfaces of adjacent phase busbars.

Distance between adjacent mechanical supports or insulators of the busbar system.

Constructional form of internal separation of functional parts, busbars, and connections within the assembly.

Number of phase current-carrying busbars provided in the product's busbar system.

Number of separate N neutral busbars provided in the product.

Number of separate PE protective busbars provided in the product.

Maximum thermal power loss that the product can dissipate under specified conditions.

Thermal power loss of the product or current-carrying system at rated current.

Maximum permissible internal temperature rise above the specified reference ambient temperature.

Factor used to reduce the permissible load relative to the rated value under specified conditions.

Ambient temperature to which the manufacturer's declared electrical or thermal characteristic applies.

Limiting current determined by the permissible temperature rise of the product or its current-carrying parts.

Current that the product can carry continuously under the manufacturer's declared conditions without exceeding permissible temperature rise.

Degree of enclosure protection against access to hazardous parts and ingress of solid objects and water, designated by the IP code.

IP degree of protection retained for accessible internal parts when the product door is open.

IP degree of protection provided by an internal enclosure, partition, or protected zone of the product.

Class of enclosure resistance to external mechanical impacts designated by the IK code.

Mechanical impact energy that the product or enclosure can withstand in the specified test.

Enclosure type or rating under the NEMA system characterizing the conditions and types of external influences against which protection is provided.

Enclosure type according to UL classification defining the declared conditions of use and types of external protection.

Indicates whether the declared ingress protection of the enclosure has been verified by certification or testing.

Method or level of protection of the user against direct contact with hazardous live parts.

Indicates whether the design prevents finger access to hazardous live parts in the intended condition.

Indicates whether the design provides protection against accidental contact with hazardous live parts.

Indicates whether a tool is required to gain access to protected internal parts of the product.

Indicates whether an internal or external protective barrier is provided to restrict access to hazardous parts.

Indicates whether insulating or mechanical protective shrouds are included with the product.

Indicates whether live parts are covered by protective elements in the intended product state.

Indicates whether the design includes measures that hinder unauthorized opening, alteration, or access.

Indicates whether the product is designed for increased resistance to deliberate mechanical impact.

Indicates whether structural provisions are provided to hinder unauthorized removal or theft of the product.

Indicates whether the design supports door interlocking depending on the state of installed equipment or a mechanism.

Indicates whether the door interlock mechanism is included with the product.

Indicates whether the design permits mechanical interlocking of devices or moving parts.

Classification of a material according to its ability to ignite, sustain combustion, and cease burning under a specified test.

Temperature of the heated wire used when testing the material or product against an ignition source.

Lowest declared glow-wire temperature at which ignition of the material is assessed according to the specified method.

Test temperature at which the resistance of insulating material to deformation under ball pressure is assessed.

Indicates whether the material ceases self-sustained burning after the ignition source is removed under specified conditions.

Indicates whether the material or construction limits flame propagation in the specified test.

Classification designation of the product's ability to maintain specified properties when exposed to fire for a defined period.

Environmental corrosivity category for which resistance of the product material or protective coating is declared.

Duration of salt-spray testing withstood by the product or coating under the declared conditions.

Indicates whether the material and coating are designed to withstand ultraviolet radiation.

Classification or test designation of material or product resistance to ultraviolet radiation.

Indicates whether the product is designed for the combination of weather influences specified by the manufacturer.

Duration of accelerated or natural weathering testing of the product.

Indicates whether the product has declared resistance to dust exposure under the specified conditions.

Indicates whether the product withstands water jets under the declared test conditions.

Indicates whether the product permits temporary immersion in water under the declared conditions.

Indicates whether the product permits continuous immersion in water under the conditions declared by the manufacturer.

Indicates whether the product is designed to withstand icing without unacceptable deterioration of declared properties.

Indicates whether the product materials retain their declared properties when exposed to the specified oils.

Indicates whether the product materials retain their declared properties when exposed to the specified coolants.

Indicates whether the product materials retain their declared properties when exposed to the specified fuels.

Groups of chemicals or environments whose effects the product can withstand under the declared conditions.

Indicates whether the product materials retain their declared properties when exposed to the specified cleaning agents.

Indicates whether the product materials retain their declared properties when exposed to ozone.

Indicates whether the product materials are suitable for operation where mould growth may occur.

Indicates whether the product materials are designed to withstand fungal organisms under the declared conditions.

Indicates the presence of structural electromagnetic shielding that reduces coupling of electromagnetic fields between the product interior and the surrounding environment.

Amount of electromagnetic field attenuation provided by the shield at the declared frequencies and measurement conditions.

Lower limit of the frequency range for which the manufacturer declares electromagnetic shielding performance.

Upper limit of the frequency range for which the manufacturer declares electromagnetic shielding performance.

Indicates the presence of a conductive gasket that maintains electromagnetic continuity of the shield at doors, covers, or joined panels.

Design method or technology used for electromagnetic shielding of the product.

Indicates the manufacturer's declared ability of the design to limit the effects of an internal electric arc under specified conditions.

Designation or classification characterizing the declared conditions and level of product resistance to an internal electric arc.

RMS current value applied during internal arc testing of the product.

Duration of internal electric arc exposure during the relevant product test.

Indicates the presence of a system for controlled relief of excess pressure from the product interior.

Designated direction for venting gases and excess pressure when the pressure-relief system operates.

Ability of the design to limit propagation of the products and effects of an internal arc fault beyond the intended zone.

Indicates the presence of a barrier intended to limit propagation of mechanical or electrical short-circuit effects between product zones.

Indicates the presence of insulating barriers separating live parts, circuits, or functional zones.

Indicates the presence of barriers between live parts of different phases to increase electrical separation.

Indicates the presence of an additional shroud or cover protecting internal components from mechanical contact or damage.

Indicates that the inspection window is designed to withstand the declared mechanical impact loads.

Classification designation of the product's mechanical security against forced entry, intrusion, or other specified influences.

Standard or method according to which the declared mechanical security rating of the product is determined.

Minimum ambient temperature at which normal operation of the product is permitted.

Maximum ambient temperature at which normal operation of the product is permitted.

Maximum permissible average ambient temperature over a consecutive 24-hour period.

Minimum ambient temperature permitted during storage of the product while not in operation.

Maximum ambient temperature permitted during storage of the product while not in operation.

Minimum ambient temperature permitted during transportation of the product.

Maximum ambient temperature permitted during transportation of the product.

Minimum ambient temperature at which the manufacturer permits installation of the product.

Maximum ambient temperature at which the manufacturer permits installation of the product.

Indicates whether permissible electrical or thermal loading must be reduced as temperature changes.

Temperature above which the permissible product load must be reduced.

Indicates whether the manufacturer has published the relationship between permissible product load and temperature.

Indicates whether the product's resistance to repeated temperature cycling has been verified.

Lower cycle temperature used during temperature-cycling testing.

Upper cycle temperature used during temperature-cycling testing.

Number of temperature cycles performed or required in the relevant test.

Indicates whether the product's resistance to rapid temperature changes between specified levels has been verified.

Temperature difference between exposure levels during thermal-shock testing of the product.

Minimum relative air humidity permitted for the declared operating or test condition.

Maximum relative air humidity permitted for the declared operating or test condition.

Temperature at which the corresponding relative humidity value is specified or standardized.

Nature of the humidity conditions for which product operation or resistance is declared.

Indicates whether the permissible humidity value applies only to non-condensing conditions.

Indicates whether the product is intended for operation where condensation may occur under the declared conditions.

Condensation or non-condensation conditions permitted during product operation.

Indicates whether the product's resistance to cyclic humidity changes has been verified.

Duration of product testing under cyclic humidity conditions.

Indicates whether the product is designed to withstand moisture caused by dew formation.

Maximum altitude above sea level at which the product may be installed without exceeding the declared conditions.

Minimum altitude relative to sea level for which the manufacturer specifies permissible installation conditions.

Indicates whether the permissible product load must be reduced as installation altitude increases.

Altitude above sea level above which the permissible product load must be reduced.

Reduction factor applied to permissible load for a specified installation altitude.

Minimum atmospheric pressure at which normal operation of the product is permitted.

Maximum atmospheric pressure at which normal operation of the product is permitted.

Types of climatic environment for which the manufacturer intends the product to be operated.

Classification level of the severity of climatic, mechanical, or other external influences.

Degree of protection of the installation location from direct exposure to the external environment.

Indicates whether the product's resistance to solar radiation has been verified.

Maximum solar radiation flux density permitted under the declared operating conditions.

Permissible or intended level of direct sunlight exposure of the product.

Permissible or intended level of direct rain exposure of the product.

Maximum rainfall intensity for which product suitability is declared.

Indicates whether the product design is intended to withstand the declared wind loads.

Maximum wind speed at which the installed product retains its declared suitability.

Maximum wind-load pressure permitted for the installed product.

Indicates whether the product is designed to withstand mechanical snow loading.

Maximum uniformly distributed snow load permitted by the product design.

Indicates whether the product is designed to withstand mechanical loading caused by ice formation.

Maximum ice-load mass per unit area permitted for the product.

Indicates whether the product's resistance to repeated freeze-thaw cycles has been verified.

Number of freeze-thaw cycles performed or required during testing.

Indicates whether the product may be operated in an environment with elevated sand and dust content.

Maximum concentration of airborne dust permitted under the declared operating conditions.

Indicates whether the product may be operated in an atmosphere with elevated salt content.

Indicates whether the product is designed for operation in a coastal atmosphere.

Indicates whether the product is designed for operation in a marine environment with characteristic salt and humidity exposure.

Indicates whether the product is designed for operation on marine and other offshore installations.

Indicates whether the product is designed for operation in an industrial atmosphere with characteristic contaminants.

Indicates whether the product is designed for operation in an agricultural environment with characteristic contaminants and humidity.

Indicates whether the product may be operated in an environment containing ammonia under the declared conditions.

Indicates whether the product may be operated in an environment containing sulfur dioxide under the declared conditions.

Indicates whether the product may be operated in an environment containing hydrogen sulfide under the declared conditions.

Indicates whether the product's resistance to vibration has been verified under the declared conditions.

Lower limit of vibration frequency applied or permitted in the relevant test.

Upper limit of vibration frequency applied or permitted in the relevant test.

Amplitude or test-method-specified acceleration of vibration applied during product testing.

Amplitude of mechanical displacement under low-frequency vibration.

Duration of vibration exposure during the specified product test.

Spatial axes along which vibration testing of the product is performed.

Indicates whether the product's resistance to short-duration mechanical shocks has been verified.

Maximum acceleration generated during mechanical shock testing of the product.

Duration of an individual mechanical shock pulse during product testing.

Number of shock impacts applied along each test axis.

Spatial axes along which mechanical shock testing of the product is performed.

Indicates whether resistance of the product or its packaging has been verified in the specified free-fall test.

Height from which the free fall is performed in the relevant test.

Number of drops performed during the relevant product or packaging test.

Classification designation of the set of external conditions permitted during transportation of the product.

Classification designation of the set of external conditions permitted during storage of the product.

Classification designation of environmental conditions during stationary operation of the product.

Classification designation of mechanical influences characteristic of the declared operating environment.

Classification designation of chemically active influences characteristic of the declared operating environment.

Classification designation of biological influences characteristic of the declared operating environment.

Standard or method used for climatic, mechanical, or combined testing of the product.

Indicates whether the product's ability to maintain declared properties under seismic effects has been verified.

Calculated or test acceleration of seismic action in the horizontal direction.

Calculated or test acceleration of seismic action in the vertical direction.

Lower limit of excitation frequency during seismic testing of the product.

Upper limit of excitation frequency during seismic testing of the product.

Classification designation of the product's seismic resistance according to the declared standard or method.

Standard or method according to which the product's seismic resistance has been verified.

Indicates whether the product is supplied assembled by the manufacturer.

Indicates whether internal electrical connections were completed by the manufacturer before delivery.

Indicates whether the manufacturer performed the specified factory checks or tests before delivery.

Indicates whether the product is supplied as a set of separate components for subsequent assembly.

Indicates whether the product or its main parts require assembly before installation and operation.

Indicates whether DIN rails are included in the product's standard equipment.

Indicates whether DIN rail end stops are included in the product's standard equipment.

Number of DIN rail end stops included in the product's standard equipment or provided for the specific version.

Indicates whether DIN rail supports are included in the product's standard equipment.

Number of DIN rail supports included in the product's standard equipment or provided for the specific version.

Indicates whether DIN rail adapters are included in the product's standard equipment.

Number of DIN rail adapters included in the product's standard equipment or provided for the specific version.

Indicates whether an N bar is included in the product's standard equipment.

Number of N terminals included in the product's standard equipment or provided for the specific version.

Indicates whether a PE bar is included in the product's standard equipment.

Number of PE terminals included in the product's standard equipment or provided for the specific version.

Indicates whether a PEN bar is included in the product's standard equipment.

Number of PEN terminals included in the product's standard equipment or provided for the specific version.

Indicates whether a phase busbar is included in the product's standard equipment.

Number of phase busbars included in the product's standard equipment or provided for the specific version.

Indicates whether a neutral busbar is included in the product's standard equipment.

Indicates whether a PE busbar is included in the product's standard equipment.

Indicates whether busbar supports are included in the product's standard equipment.

Number of busbar supports included in the product's standard equipment or provided for the specific version.

Indicates whether busbar protective covers are included in the product's standard equipment.

Number of busbar covers included in the product's standard equipment or provided for the specific version.

Indicates whether busbar insulators are included in the product's standard equipment.

Number of busbar insulators included in the product's standard equipment or provided for the specific version.

Types of current-carrying busbars included in the product's standard equipment.

Indicates whether terminal blocks are included in the product's standard equipment.

Number of terminal blocks included in the product's standard equipment or provided for the specific version.

Types of terminals or terminal blocks included in the product's standard equipment.

Indicates whether spare terminals are included in the product's standard equipment.

Number of spare terminals included in the product's standard equipment or provided for the specific version.

Indicates whether terminal markers are included in the product's standard equipment.

Number of terminal markers included in the product's standard equipment or provided for the specific version.

Indicates whether terminal jumpers are included in the product's standard equipment.

Number of terminal jumpers included in the product's standard equipment or provided for the specific version.

Indicates whether terminal end clamps are included in the product's standard equipment.

Number of terminal end clamps included in the product's standard equipment or provided for the specific version.

Indicates whether modular blanking plates are included in the product's standard equipment.

Number of modular blanking plates included in the product's standard equipment or provided for the specific version.

Indicates whether modular covers are included in the product's standard equipment.

Number of modular covers included in the product's standard equipment or provided for the specific version.

Indicates whether a label holder is included in the product's standard equipment.

Number of label holders included in the product's standard equipment or provided for the specific version.

Indicates whether equipment labels are included in the product's standard equipment.

Number of equipment labels included in the product's standard equipment or provided for the specific version.

Indicates whether circuit labels are included in the product's standard equipment.

Number of circuit labels included in the product's standard equipment or provided for the specific version.

Indicates whether warning labels are included in the product's standard equipment.

Indicates whether a rating label is included in the product's standard equipment.

Indicates whether a nameplate is included in the product's standard equipment.

Indicates whether a wiring duct is included in the product's standard equipment.

Number of wiring ducts included in the product's standard equipment or provided for the specific version.

Indicates whether wiring duct covers are included in the product's standard equipment.

Indicates whether wire holders are included in the product's standard equipment.

Number of wire holders included in the product's standard equipment or provided for the specific version.

Indicates whether cable ties are included in the product's standard equipment.

Number of cable ties included in the product's standard equipment or provided for the specific version.

Indicates whether cable markers are included in the product's standard equipment.

Number of cable markers included in the product's standard equipment or provided for the specific version.

Indicates whether wire markers are included in the product's standard equipment.

Number of wire markers included in the product's standard equipment or provided for the specific version.

Indicates whether wire-end ferrules are included in the product's standard equipment.

Number of wire-end ferrules included in the product's standard equipment or provided for the specific version.

Indicates whether an accessory pack is included in the product's standard equipment.

Composition or type of the additional accessory pack supplied with the product.

Indicates whether spare parts are included in the product's standard equipment.

List of spare parts included with the product.

Indicates whether an installation hardware kit is included in the product's standard equipment.

Indicates whether a protective bonding kit is included in the product's standard equipment.

Indicates whether touch-up paint is included in the product's standard equipment.

Indicates whether sealing plugs are included in the product's standard equipment.

Number of sealing plugs included in the product's standard equipment or provided for the specific version.

Indicates whether documentation is included in the product's standard supply.

Indicates whether an installation manual is included with the product.

Indicates whether assembly instructions are included with the product.

Indicates whether a wiring diagram is included with the product.

Indicates whether a terminal diagram is included with the product.

Indicates whether a single-line diagram is included with the product.

Indicates whether a parts list is included with the product.

Languages in which the manufacturer provides documentation included with or available for the product.

Indicates whether a QR code is provided for access to the product's electronic documentation.

Indicates the presence of an inspection window allowing visual reading of an installed meter without opening the main enclosure.

Number of inspection windows provided by design for metering devices.

Design type of inspection window intended for visual access to the metering device.

Horizontal dimension of the clear or structural opening of the window intended for viewing the metering device.

Vertical dimension of the clear or structural opening of the window intended for viewing the metering device.

Indicates whether the meter window or the element providing access through it can be sealed.

Indicates whether the product is structurally prepared for installation of a revenue or technical electricity metering arrangement.

Indicates the presence of a separate internal compartment intended for metering devices and components.

Indicates whether the separate metering compartment can be sealed to control access to installed equipment.

Indicates the presence of a separate section for multimedia, telecommunications, or extra-low-voltage equipment.

Indicates structural separation of the multimedia section from other internal zones of the product.

Indicates the presence of a separate section for extra-low-voltage and signal circuits or equipment.

Indicates the presence of a separate section for power circuits and electrical equipment.

Indicates structural separation of power and extra-low-voltage circuits or their installation zones.

Indicates the presence of a separate section for communication and network equipment.

Indicates the presence of a separate section for control devices and associated circuits.

Indicates the presence of a separate section for automation devices, controllers, and interface components.

Indicates whether the position or configuration of internal partitions can be changed using provisions built into the design.

Method of providing air exchange inside the product, including natural or forced ventilation.

Number of separate ventilation openings or elements provided by the product design.

Total free area of openings through which ventilation air can flow.

Indicates whether natural air exchange is provided without the use of fans.

Indicates whether the design permits fans or other means of forced air exchange.

Indicates whether the design permits installation of a fan for forced circulation or air extraction.

Indicates whether a fan is included in the product's standard equipment.

Number of fans installed in the product or included in its declared equipment.

Volume of air moved by the fan per unit time under the declared operating conditions.

Rated electrical supply voltage of the fan.

Rated input or declared electrical power of the fan.

Type of electrical current required to supply the fan.

Indicates whether the design permits installation of a filter fan for forced air exchange with filtration of incoming air.

Indicates whether a filter fan is included in the product's standard equipment.

Number of filter fans installed in the product or included in its declared equipment.

Volume of air moved by the filter fan per unit time under the declared conditions.

Classification of the air filter according to its particle-retention capability under the classification system declared by the manufacturer.

Indicates whether an exhaust air filter for the ventilation path is included.

Indicates whether the design permits installation of a fan in the top or roof section of the product.

Indicates whether a roof fan is included in the product's standard equipment.

Indicates whether provision is made for installation of an internal heater.

Indicates whether a heater is included with the product.

Number of heaters installed in or supplied with the product.

Total rated electrical power of all provided heaters.

Rated supply voltage of the provided heater.

Type of electrical current used to supply the heater.

Indicates whether provision is made for installation of a thermostat for temperature control.

Indicates whether a thermostat is included with the product.

Minimum temperature that can be set as the setpoint of the provided thermostat.

Maximum temperature that can be set as the setpoint of the provided thermostat.

Indicates whether provision is made for installation of a hygrostat for humidity-based control.

Indicates whether a hygrostat is included with the product.

Minimum relative humidity that can be set as the setpoint of the provided hygrostat.

Maximum relative humidity that can be set as the setpoint of the provided hygrostat.

Indicates whether heating is provided to reduce the risk of condensation inside the product.

Indicates whether the design permits installation of an active cooling unit to remove heat from the internal space.

Indicates whether an active cooling unit is included in the product's standard equipment.

Thermal power that the cooling unit can remove under the declared operating conditions.

Rated electrical supply voltage of the cooling unit.

Type of electrical current required to supply the cooling unit.

Indicates whether the design permits installation of a heat exchanger to transfer heat between internal and external environments without direct mixing of air streams.

Indicates whether a heat exchanger is included in the product's standard equipment.

Thermal power that the heat exchanger can transfer under the declared operating conditions.

Indicates the presence of a thermal-insulation layer that reduces heat transfer through the product enclosure.

Thickness of the thermal-insulation layer provided by the product design.

Material used in the product to reduce heat transfer through its enclosure.

Indicates whether a system is provided for controlled removal of liquid that has entered or condensed inside the product.

Indicates whether a dedicated drain is provided for removing condensate from the product.

Indicates whether the design permits installation of an internal light for illuminating the service area.

Indicates whether an internal light is included in the product's standard equipment.

Type of light source or luminaire used for internal illumination of the product.

Rated electrical power of the internal light.

Rated electrical supply voltage of the internal light.

Indicates automatic control of the internal lighting by a switch linked to the door position.

Indicates whether the design permits installation of an internal or service socket outlet.

Indicates whether a service socket outlet is included in the product's standard equipment.

Type or standard of the service socket outlet.

Rated voltage for which the service socket outlet is designed.

Rated current for which the service socket outlet is designed.

Indicates whether the design permits installation of a switch or sensor for monitoring the door position.

Indicates whether a door-position switch or sensor is included in the product's standard equipment.

Indicates whether the design permits installation of a sensor for measuring temperature inside the product or on its components.

Indicates whether a temperature sensor is included in the product's standard equipment.

Indicates whether the design permits installation of a sensor for measuring relative humidity inside the product.

Indicates whether a humidity sensor is included in the product's standard equipment.

Indicates whether the design permits installation of a smoke detection device inside the product.

Indicates whether a smoke detector is included in the product's standard equipment.

Indicates whether the design permits installation of a sensor for detecting water or another conductive liquid.

Indicates whether a water-leak sensor is included in the product's standard equipment.

Indicates whether a discrete alarm signal can be generated through the provided signalling contact.

Indicates whether an alarm signalling contact is included in the product's standard equipment.

Indicates whether the product is structurally or interface-ready for connection to remote condition or parameter monitoring systems.

Indicates the presence of handles designed for manual carrying or movement of the product.

Number of handles provided by design for manual carrying or movement of the product.

Design type of handle intended for manual carrying or movement of the product.

Indicates whether transport wheels can be installed as provided by the product design or compatible accessory system.

Indicates whether transport wheels are included in the product's standard equipment.

Number of transport wheels fitted to the product or included in its declared equipment.

Indicates the presence or support of a transport-wheel braking mechanism to prevent unintended movement of the product.

Indicates the presence of designed lifting points for safely raising the product with lifting equipment.

Type of structural element provided as a lifting point for the product.

Number of lifting points provided by the product design.

Indicates whether accessories for lifting or slinging the product are included.

Indicates whether the design permits installation of an additional protective roof above the product.

Indicates whether an additional protective roof is included in the product's standard equipment.

Indicates whether the design permits installation of a hood that reduces direct precipitation exposure of the product.

Indicates whether a rain hood is included in the product's standard equipment.

Indicates whether the design permits installation of a shield that reduces direct solar heating of the product.

Indicates whether a sun shield is included in the product's standard equipment.

Indicates whether the product's side panels can be removed without damaging its main supporting structure.

Indicates whether the product's rear panel can be removed without damaging its main supporting structure.

Indicates whether the product's top panel or roof can be removed without damaging its main supporting structure.

Regions or markets for which the manufacturer declares regulatory or certification compliance of the product.

Certification, market-approval, or conformity marks applicable to the product.

Primary normative document or standard according to which the manufacturer classifies or assesses the product.

Additional normative documents and standards declared by the manufacturer as applicable to the product.

Indicates whether an official declaration of conformity is available for the product.

Indicates whether a separate manufacturer declaration concerning declared product characteristics or conformity is available.

Indicates whether a certificate relating to the declared certification or conformity of the product is available.

Identification number of the certificate relating to the product or its certified version.

Name of the organization that issued the certificate or performed the relevant conformity assessment.

Indicates whether the product was tested by an organization independent of the manufacturer.

Indicates whether a test report confirming the declared product characteristics is available.

Indicates whether a type-test report for the product or relevant design is available.

Indicates whether a report of routine or acceptance tests on the manufactured product is available.

Indicates whether documented confirmation of design verification for the product or assembly is available.

Methods used to verify that the design complies with the declared requirements.

Indicates whether periodic production inspection is required to maintain the declared certification.

Indicates whether the CE marking is applied to the product where applicable.

Indicates whether the UKCA marking is applied to the product where applicable.

Indicates whether the EAC marking is applied to the product where applicable.

Indicates whether the product has a declared UL Listed certification or recognition status.

Indicates whether the product has a declared UL Recognized certification or recognition status.

Indicates whether the cULus mark is applied to the product where applicable.

Indicates whether the product has a declared CSA certification or recognition status.

Indicates whether the product has a declared TÜV certification or recognition status.

Indicates whether the product has a declared VDE certification or recognition status.

Indicates the presence of a valid DNV approval for the product within the application scope specified by the manufacturer.

Indicates the presence of a valid Lloyd's Register approval for the product within the application scope specified by the manufacturer.

Indicates the presence of a valid Bureau Veritas approval for the product within the application scope specified by the manufacturer.

Indicates the presence of a valid American Bureau of Shipping approval for the product within the application scope specified by the manufacturer.

Indicates the presence of an approval or certification for use of the product on marine vessels or in marine technical systems.

Indicates the presence of an approval or certification for use of the product on railway rolling stock or in railway infrastructure.

Indicates the presence of a manufacturer-declared approval for use of the product in hazardous areas under specified conditions.

Indicates declared conformity of the product with applicable ATEX requirements for equipment intended for potentially explosive atmospheres.

Indicates certification of the product under the international IECEx system for equipment used in explosive atmospheres.

Declared classification of the hazardous atmosphere or operating location for which the product is intended.

Complete explosion-protection marking of the product containing the classification and protection markings declared by the manufacturer.

List of hazardous zones in which the product may be used according to the declared classification.

Equipment group for the explosion-protected version, defining its intended application area and conditions.

ATEX equipment category characterizing the required protection level and permitted application area in an explosive atmosphere.

Type or combination of explosion-protection concepts used in the product design to prevent ignition of the surrounding explosive atmosphere.

Indicates whether the manufacturer declares product compliance with IEC 62208.

Indicates whether the manufacturer declares product compliance with EN 62208.

Indicates whether the manufacturer declares product compliance with IEC 61439-1.

Indicates whether the manufacturer declares product compliance with EN IEC 61439-1.

Indicates whether the manufacturer declares product compliance with IEC 61439-2.

Indicates whether the manufacturer declares product compliance with EN IEC 61439-2.

Indicates whether the manufacturer declares product compliance with IEC 61439-3.

Indicates whether the manufacturer declares product compliance with EN IEC 61439-3.

Indicates whether the manufacturer declares product compliance with IEC 60529.

Indicates whether the manufacturer declares product compliance with EN 60529.

Indicates whether the manufacturer declares product compliance with IEC 62262.

Indicates whether the manufacturer declares product compliance with EN 62262.

Indicates whether the manufacturer declares product compliance with IEC 60670-1.

Indicates whether the manufacturer declares product compliance with IEC 60670-24.

Indicates whether the manufacturer declares product compliance with UL 50.

Indicates whether the manufacturer declares product compliance with UL 50E.

Indicates whether the manufacturer declares product compliance with NEMA 250.

Indicates whether the product has been tested according to applicable methods of the IEC 60068 series.

Indicates whether product compliance with applicable RoHS restrictions on hazardous substances has been declared.

Indicates whether a manufacturer declaration of product compliance with RoHS requirements is available.

Indicates whether the manufacturer declares compliance of the product with applicable REACH Regulation requirements.

Indicates whether a manufacturer declaration concerning compliance with REACH requirements is available.

Indicates whether a manufacturer declaration concerning substances on the REACH SVHC list is available.

Indicates whether product compliance with applicable China RoHS requirements has been declared.

Indicates whether the product falls within the scope of WEEE requirements for waste electrical and electronic equipment.

Indicates whether a manufacturer declaration relating to California Proposition 65 requirements is available.

Indicates whether a manufacturer declaration concerning the origin and use of regulated conflict minerals is available.

Indicates whether a manufacturer declaration concerning the presence or absence of PFAS substances is available.

Indicates whether an Environmental Product Declaration (EPD) is available for the product or relevant product group.

Indicates whether product carbon footprint data have been published for the product or relevant product group.

Indicates whether a declaration of compliance of the materials used with specified requirements or restrictions is available.

Additional manufacturer information concerning standards, certificates, declarations, and limitations of the declared compliance scope.

Mass of the product together with its individual packaging and the accessories included in it.

External horizontal dimension of the product's individual package.

External vertical dimension of the product's individual package.

External depth dimension of the product's individual package.

Calculated or declared external volume of the product's individual package.

Design type of the product's individual or transport packaging.

Primary materials from which the product packaging is made.

Mass of the empty packaging without the product and its accessories.

Number of individual products contained in one packaging unit at the specified level.

Number of products in the inner group package.

Number of products in the outer group or transport package.

Indicates whether the packaging used is declared recyclable as secondary raw material.

Indicates whether the packaging is designed for reuse without changing its primary purpose.

Indicates whether the packaging is intended to be returned to the supplier, manufacturer, or another participant in the logistics chain.

Indicates whether the packaging is intended for single use.

Indicates whether the absence of plastic materials in the product packaging has been declared.

Total mass of plastic packaging components in one packaging unit.

Total mass of paper and cardboard packaging components in one packaging unit.

Total mass of wooden packaging components in one packaging unit.

Total mass of metal packaging components in one packaging unit.

Indicates whether separate elements are provided in the packaging to protect corners against mechanical damage.

Indicates whether separate elements are provided in the packaging to protect edges against mechanical damage.

Indicates whether the package is closed in a manner that limits free ingress of air, moisture, or contaminants to the declared degree.

Number of products or packaging units contained in one transport carton.

External horizontal dimension of the transport carton.

External vertical dimension of the transport carton.

External depth dimension of the transport carton.

Calculated or declared external volume of the transport carton.

Mass of the contents of the transport carton excluding the mass of the carton itself and its packaging materials.

Total mass of the transport carton including its contents and packaging materials.

Number of products or inner packaging units contained in a master carton.

External horizontal dimension of the master carton.

External vertical dimension of the master carton.

External depth dimension of the master carton.

Calculated or declared external volume of the master carton.

Total mass of the master carton including its contents and packaging materials.

Indicates whether the product or group packaging is supplied secured on a transport pallet.

Type or design of the pallet used for transport and storage of the load.

Number of individual product units placed on one fully assembled pallet.

Number of cartons or transport cardboard packages placed on one pallet.

Number of horizontal layers of goods or packages on a fully assembled pallet.

Number of product units placed in one horizontal pallet layer.

Overall external longitudinal dimension of the assembled loaded pallet.

Overall external transverse dimension of the assembled loaded pallet.

Overall external height of the assembled loaded pallet from the bottom supporting surface to the highest point.

Total mass of the products on the pallet excluding the mass of the pallet itself and transport packaging.

Total mass of the assembled pallet including products, pallet, and transport packaging.

External volume of the assembled pallet load determined by its transport dimensions.

Indicates whether assembled pallets may be stacked one on another under the declared storage or transport conditions.

Maximum number of tiers of assembled pallets permitted when stacked vertically.

Maximum total mass of a pallet stack permitted under the declared storage or transport conditions.

Permissible spatial orientation of the packaged product during transportation.

Permissible spatial orientation of the packaged product during storage.

Indicates whether the package must be kept upright during storage and transportation.

Indicates whether the load requires careful handling because of sensitivity to mechanical impact or dropping.

Indicates whether the packaging and product must be protected from rain, water, and other sources of moisture.

Indicates whether the product or its packaging is sensitive to elevated air humidity.

Indicates whether the product or packaging must be protected from direct solar radiation.

Indicates whether the product or packaging must be protected from elevated temperatures and heat sources.

Indicates whether the product must be protected from temperatures below the permissible value during storage or transportation.

Indicates whether placing other packaging units on top is prohibited during storage or transportation.

Maximum number of packaging layers permitted when stacking.

Maximum load mass that may be placed on top of a packaging unit.

Indicates whether the packaging has a handle or other standard feature for manual carrying.

Indicates whether the packaging or transport base allows safe insertion of forklift forks for moving the load.

Indicates whether the packaging or transport structure permits crane lifting using designated points or elements.

Indicates the presence of an indicator that records when a specified mechanical shock threshold acting on the package is exceeded.

Indicates the presence of an indicator that records tilting of the package beyond the specified permissible position.

Indicates the presence of an indicator for monitoring humidity exposure inside the packaging or during transportation.

Indicates the presence of moisture-absorbing material in the packaging to reduce moisture content within the package.

Indicates the use of a volatile corrosion inhibitor (VCI) in the packaging to protect metal surfaces during storage and transportation.

Indicates sealed packaging from which part of the air is removed before final sealing.

Indicates the use of packaging materials or measures intended to reduce the risk of product corrosion during storage and transportation.

Indicates the need to maintain a specified temperature range during product transportation.

Minimum ambient relative humidity permitted for the product during transportation.

Maximum ambient relative humidity permitted for the product during transportation.

Indicates the need to control and maintain relative humidity within a specified range during transportation.

Modes of transport for which the manufacturer intends the product to be carried in the declared transport packaging.

Indicates whether the packaged product is suitable for transport in a freight container under the declared conditions.

Types of freight containers permitted by the manufacturer for transporting the packaged product.

Indicates the use of transport packaging specially prepared for international or long-duration export shipment.

Indicates the use of transport packaging intended for sea transport and prolonged exposure to the climatic factors characteristic of it.

Indicates whether the product or substances contained in it are classified as dangerous goods for transport.

Dangerous-goods class or division assigned to the product or a substance contained in it for transport purposes.

Four-digit United Nations number identifying a dangerous substance or article during international transport.

Packing group characterizing the degree of hazard of regulated goods for selection of packaging requirements, where applicable.

Indicates whether dangerous goods may be transported under the Limited Quantity (LQ) provisions when the applicable conditions are met.

Indicates whether dangerous goods may be transported under the Excepted Quantity (EQ) provisions when the applicable conditions are met.

Country of origin of the goods declared for customs or commercial purposes.

Country in which the product was manufactured or its principal manufacturing operation was performed.

Commodity code under the international Harmonized Commodity Description and Coding System.

Commodity code under the Combined Nomenclature of the European Union.

Tariff classification code used for customs clearance of the goods in the relevant jurisdiction.

U.S. Export Control Classification Number assigned to the item where applicable.

Indicates whether preferential origin is declared for the goods under an applicable trade agreement or preferential regime.

Agreement, scheme, or basis under which preferential origin of the goods is declared.

Indicates whether a declaration or other document confirming the declared origin of the goods is available.

Machine-readable barcode applied to the relevant packaging unit.

Global Trade Item Number (GTIN) assigned to the transport carton or the logistics unit contained in it.

Global Trade Item Number (GTIN) assigned to the pallet packaging configuration where applicable.

Indicates whether identification of the logistics unit using an SSCC code is supported.

Indicates whether the logistics unit is supplied with a label containing an SSCC code.

Types of logistics labels and identification formats used on the packaging or load unit.

Handling and warning symbols applied to packaging to specify requirements for handling the load.

Standard, specification, or requirements system according to which the product packaging is made.

Indicates whether the wooden packaging used is declared compliant with ISPM 15 requirements where applicable.

Indicates whether a fumigation or wood-packaging treatment certificate is available where such a document applies.

Indicates whether a limited storage period is specified for the product before commissioning or use.

Duration of the specified product storage period in months when the declared conditions are maintained.

Additional information concerning transportation, storage, packaging, marking, or customs handling of the product.