External horizontal dimension of the product between its outermost lateral points.

External vertical dimension of the product from its lowest to its highest point.

External distance between the foremost and rearmost surfaces of the product.

Mass of the product itself, excluding transport packaging, additional accessories, and external equipment.

Primary visually perceived colour of the product's external surface.

Primary material from which the product is manufactured.

Permissible spatial orientation of the component during installation and operation.

Installation arrangement permitted by the product design, such as wall-mounted, flush-mounted, floor-mounted, or another specified mounting type.

Method used to mechanically secure the product to a support, surface, or load-bearing structure.

Voltage value assigned to the product by the manufacturer for specified application conditions and characteristics.

AC frequency assigned to the product for normal operating conditions.

Number of phases of the electrical system for which the product is designed to be connected or used.

Current assigned to the product by the manufacturer for the declared operating and thermal conditions.

Maximum nominal conductor cross-section permitted at the product's incoming connection.

Maximum nominal conductor cross-section permitted at the product's outgoing connection.

Voltage with reference to which the product's insulation clearances and dielectric properties are specified.

Peak value of an impulse voltage of specified waveform that the product insulation must withstand without breakdown.

Minimum conductor cross-section permitted for connection to the incoming terminal of the main power circuit.

Minimum conductor cross-section permitted for connection to the outgoing terminal of the main power circuit.

Indicates whether the product can measure and provide electrical voltage values.

Indicates whether the product can measure and provide electrical current values.

Indicates whether the product can measure and provide electrical network frequency values.

Indicates whether measurement or cumulative metering of electrical energy is supported.

Indicates whether current unbalance measurement or calculation is supported.

Indicates whether voltage unbalance measurement or calculation is supported.

Number of electrical connection points intended for incoming or supply-side connections.

Number of electrical connection points intended for outgoing or load-side connections.

Electrical connection technologies supported at the incoming or supply-side connection points of the product.

Electrical connection technologies supported at the outgoing or load-side connection points of the product.

Manufacturer-declared tightening torque for an incoming or supply terminal.

Manufacturer-declared tightening torque for an outgoing or load-side terminal.

Indicates that the current transformer ratio used for measurement scaling can be configured in the device.

Minimum configurable primary current value used for current transformer scaling.

Maximum configurable primary current value used for current transformer scaling.

Standard secondary current ratings of external current transformers supported by the measuring input.

Indicates that active electrical power is measured or calculated by the device.

Indicates that reactive electrical power is measured or calculated by the device.

Indicates that apparent electrical power is measured or calculated by the device.

Indicates that the electrical power factor is measured or calculated by the device.

Current type of the monitored voltage measuring circuit: AC, DC or AC/DC.

Lower limit of the manufacturer-declared voltage measuring range.

Upper limit of the manufacturer-declared voltage measuring range.

Manufacturer-declared accuracy of voltage measurement where expressed as a single percentage value.

Lower limit of the manufacturer-declared frequency measurement range.

Upper limit of the manufacturer-declared frequency measurement range.

Manufacturer-declared absolute accuracy of frequency measurement.

Lower limit of the manufacturer-declared current measuring range.

Upper limit of the manufacturer-declared current measuring range.

Manufacturer-declared relative accuracy of current measurement where expressed as a percentage.

Minimum configurable primary-to-secondary current transformer ratio.

Maximum configurable primary-to-secondary current transformer ratio.

Lower limit of the manufacturer-declared active-power measuring range.

Upper limit of the manufacturer-declared active-power measuring range.

Manufacturer-declared relative accuracy of active-power measurement.

Lower limit of the manufacturer-declared reactive-power measuring range.

Upper limit of the manufacturer-declared reactive-power measuring range.

Manufacturer-declared relative accuracy of reactive-power measurement.

Lower limit of the manufacturer-declared apparent-power measuring range.

Upper limit of the manufacturer-declared apparent-power measuring range.

Manufacturer-declared relative accuracy of apparent-power measurement.

Lower limit of the manufacturer-declared power-factor measuring range.

Upper limit of the manufacturer-declared power-factor measuring range.

Manufacturer-declared absolute accuracy of power-factor measurement expressed as a cos φ value difference.

Overall electrical measurement connection topology of the device, distinguishing direct measurement and operation through external current, voltage, shunt, Rogowski or sensor interfaces.

Supported methods for connecting the voltage measuring circuit, such as direct connection or connection through an external voltage transformer.

Indicates that the measuring device supports voltage measurement through an external voltage transformer.

Indicates that the voltage transformer ratio used for measurement scaling can be configured in the device.

Minimum configurable primary voltage value used for voltage-transformer measurement scaling.

Maximum configurable primary voltage value used for voltage-transformer measurement scaling.

Standard secondary voltage ratings of external voltage transformers supported by the measuring input.

Indicates separate measurement or registration of energy flowing in both import and export directions.

Indicates support for four-quadrant measurement of active and reactive power or energy, distinguishing direction and reactive quadrant where applicable.

Indicates that measured electrical quantities are available separately for individual phases.

Indicates that phase-to-phase voltage values can be measured and made available by the device.

Indicates that phase-to-neutral voltage values can be measured and made available by the device.

Indicates that current in the neutral conductor can be measured independently.

Indicates that aggregate or total system values are calculated in addition to individual phase measurements.

Indicates that the device measures or accumulates active electrical energy.

Indicates that the device measures or accumulates reactive electrical energy.

Indicates that the device measures or accumulates apparent electrical energy.

Indicates separate measurement or accumulation of imported energy.

Indicates separate measurement or accumulation of exported energy.

Indicates calculation or accumulation of net energy resulting from import and export energy flow.

Reactive-energy quadrants that can be separately measured or registered.

Manufacturer-declared accuracy class for active electrical energy measurement.

Manufacturer-declared accuracy class for reactive electrical energy measurement.

Reference current Iref declared for an electricity meter where applicable.

Basic current Ib declared for a direct-connected electricity meter where applicable.

Minimum current Imin associated with the declared metrological performance of the meter.

Transition current Itr associated with the declared metrological accuracy region of the meter.

Minimum current at which the electricity meter starts and continues energy registration under declared conditions.

Maximum meter current Imax associated with the declared metrological current range.

Indicates that energy values can be accumulated separately in multiple tariff registers.

Maximum number of independent energy tariffs supported by the meter.

Methods supported for selecting or switching active tariff registers.

Indicates the presence of a cumulative total-energy register.

Indicates the presence of one or more partial or subtotal energy registers.

Indicates that a partial energy register can be reset without clearing the legally relevant total-energy register.

Indicates storage of the maximum calculated demand value.

Indicates that the demand calculation interval can be configured.

Minimum configurable interval used for demand calculation.

Maximum configurable interval used for demand calculation.

Indicates that time-series load or energy profile data can be recorded internally.

Minimum configurable interval between stored load-profile records.

Maximum configurable interval between stored load-profile records.

Maximum number of load-profile records retained internally.

Indicates that accumulated energy can be represented by an electrical pulse output.

Number of output pulses corresponding to one kilowatt-hour of active energy.

Number of output pulses corresponding to one kilovar-hour of reactive energy.

Duration of a single energy pulse generated by the pulse output.

Electrical implementation of the pulse output used for metering or counting.

Indicates the presence of an optical metrology LED generating pulses proportional to measured energy.

Number of optical metrology LED pulses corresponding to one kilowatt-hour.

Indicates that the phase angle between relevant voltage and/or current quantities can be measured or calculated.

Indicates measurement or calculation of total harmonic distortion of voltage.

Indicates measurement or calculation of total harmonic distortion of current.

Indicates that one or more terminal blocks can be removed from the device body for wiring or service.

Indicates that one or more electrical terminal blocks use a pluggable disconnectable connection system.

Centre-to-centre pitch between adjacent electrical terminals in the relevant terminal row.

Indicates that electrical connection terminals are individually identified by manufacturer-applied markings.

Physical directions from which conductors or tools access the electrical connection terminals.

Minimum conductor cross-section accepted by the relevant general device terminal connection.

Maximum conductor cross-section accepted by the relevant general device terminal connection.

Indicates that the terminal cover can be sealed or plombed against unauthorized access.

Indicates that incorrect current-transformer polarity or reversed current measurement direction can be detected.

Indicates that an incorrect relationship between voltage and current phase channels can be detected.

Indicates that electrical quantities or energy can be measured independently for individual charging points.

Indicates that energy transferred during an individual EV charging session can be measured or accumulated separately.

Indicates that a meter reading corresponding to the beginning of a charging transaction or session can be recorded or reported.

Indicates that a meter reading corresponding to the end of a charging transaction or session can be recorded or reported.

Indicates that electrical meter values can be periodically transmitted or reported to another device or backend system.

Minimum configurable interval between periodic meter-value reports.

Maximum configurable interval between periodic meter-value reports.

Indicates that metering data can be cryptographically signed or otherwise protected for authenticity and integrity verification.

Indicates that historical records of EV charging sessions can be retained locally or in an integrated logging subsystem.

Maximum number of charging-session records that can be retained by the product where manufacturer-declared.

Indicates that the cumulative number of charging sessions can be retained as an operating statistic.

Indicates that cumulative active EV charging time can be retained as an operating statistic.

Indicates that cumulative energy transferred toward connected EVs can be retained as a lifetime operating statistic.

Degree of enclosure protection against access to hazardous parts and ingress of solid objects and water, designated by the IP code.

Class of enclosure resistance to external mechanical impacts designated by the IK code.

Indicates detection or signalling of reverse energy flow.

Indicates that accumulated energy registers are retained without normal supply voltage.

Indicates that energy register values are preserved across supply interruptions.

Indicates that the meter can detect and register manufacturer-defined tamper or manipulation events.

Minimum ambient temperature at which normal operation of the product is permitted.

Maximum ambient temperature at which normal operation of the product is permitted.

Minimum ambient temperature permitted during storage of the product while not in operation.

Maximum ambient temperature permitted during storage of the product while not in operation.

Maximum relative air humidity permitted for the declared operating or test condition.

Maximum altitude above sea level at which the product may be installed without exceeding the declared conditions.

Indicates whether the product has an integrated local display.

Technology or construction type of the product's integrated display.

Indicates whether the integrated display has a backlight.

Number of integrated LEDs used to indicate product status or operating modes.

Physical diagonal dimension of the integrated display viewing area.

Number of predefined or configurable local display pages available for measured values or device information.

Indicates that the device can automatically cycle through display pages or measured values.

Indicates that the measurement unit associated with a displayed value is shown locally.

Indicates that local measured-value presentation identifies the associated phase or conductor.

Indicates that local configuration access can be intentionally restricted against unauthorized changes.

Methods supported for restricting access to local device configuration.

Indicates whether the product can store an internal event log.

Maximum number of event records that can be stored in the product's internal log.

Indicates whether an integrated real-time clock is provided for timekeeping, event time-stamping, or time-based functions.

List of supported digital data communication protocols.

List of supported physical or logical digital communication interfaces.

Indicates whether an integrated web server or web interface is provided for access to product functions.

Indicates whether specified product settings can be read or changed remotely through a supported communication interface.

Indicates whether diagnostic information, status data, or fault information can be obtained remotely.

Indicates that device firmware can be updated by a manufacturer-supported procedure.

Number of integrated physical Ethernet communication ports.

Indicates that measured electrical values can be stored internally as historical measurement records.

Maximum number of historical measurement records retained internally.

Indicates that the interval between periodic measurement records can be configured.

Minimum configurable interval between periodically stored measurement records.

Maximum configurable interval between periodically stored measurement records.

Supported conditions or commands that initiate storage of measurement records.

Manufacturer-declared internal non-volatile memory capacity available for measurement history or logging.

Indicates that stored measurement or event history can be exported from the device.

File or interchange formats supported for exporting stored measurement data.

Indicates that alarm occurrences are stored in a dedicated alarm history or log.

Maximum number of alarm records retained in the dedicated alarm history.

Indicates that active or stored alarms can be explicitly acknowledged by the user or supervisory system.

Indicates that the stored maximum demand register can be reset using a manufacturer-supported procedure.

Indicates that stored minimum and maximum measured values can be reset.

Supported serial communication baud rates for interfaces such as RS-232, RS-422, RS-485 or equivalent serial buses.

Supported data-word lengths for serial communication.

Parity modes supported by the serial communication interface.

Supported number of stop bits in serial communication frames.

Indicates that the logical device or slave address used by a serial communication protocol can be configured.

Minimum configurable logical address on a supported serial communication network.

Maximum configurable logical address on a supported serial communication network.

Supported nominal Ethernet physical-layer link speeds.

Supported methods for assigning network-layer addresses to the Ethernet interface.

Indicates support for Internet Protocol version 6 communication.

Indicates that one or more integrated or optional wireless communication technologies are supported.

Wireless communication technologies supported by the product.

Cellular network technologies supported by the integrated or optional modem.

Physical or embedded SIM formats supported by a cellular communication module.

Indicates that an external antenna can be connected for wireless or cellular data communication.

Indicates that wireless or cellular signal-strength information is available locally or through communication.

Indicates that measured or logged data can be transmitted automatically without an explicit polling request.

Indicates manufacturer-supported communication with a cloud or remote Internet service.

Indicates that measurement, status or configuration data can be accessed through a documented application programming interface.

Application programming interface types supported by the product or its integrated communication service.

Indicates that firmware can be updated through a supported local or remote data communication interface.

Indicates that loss or inactivity of a communication link can be detected by an internal communication watchdog.

Indicates that access to network, web, API or remote configuration functions can require authenticated user credentials.

Indicates support for encrypted data communication through one or more manufacturer-supported communication services.

Transport Layer Security protocol versions supported for protected network communication.

Indicates that user permissions can be differentiated by user role or authorization level.

Indicates that security-relevant events such as authentication failures or configuration access can be recorded.

Indicates that the device verifies the integrity or authenticity of executable firmware during startup.

Indicates that firmware update packages are cryptographically authenticated before installation.

Indicates that loss of an expected communication connection can generate a local or remote alarm or diagnostic condition.

Indicates whether the CE marking is applied to the product where applicable.

Indicates that the product is intended for a measurement application subject to legal metrology requirements.

Indicates manufacturer-declared approval for legally regulated or commercial measurement use in at least one applicable jurisdiction.

Indicates suitability for revenue or billing energy metering where the manufacturer explicitly declares such use.

Compliance with Directive 2014/32/EU on measuring instruments where applicable.

Indicates that the product falls within the MID MI-003 category for active electrical energy meters.

MID conformity assessment procedures under which the active electrical energy meter may be assessed.

Indicates that legally required metrological marking is applied to the product where applicable.

Indicates presence of the supplementary metrology marking required by the applicable European measuring-instrument conformity scheme.

Identification number of the notified body associated with the applicable conformity assessment or metrological marking.

Indicates that a type-approval or equivalent legal-metrology approval exists for the product.

Manufacturer- or authority-declared identifier of the applicable legal-metrology type approval.

Indicates that metrological sealing is required to protect legally relevant settings or measurement access.

Indicates that dedicated provisions exist for applying a metrological seal.

Indicates that the catalog product is normally supplied with manufacturer-applied metrological sealing where applicable.

Indicates that the measuring function can be calibrated using a manufacturer-defined procedure.

Indicates that the product is calibrated by the manufacturer before delivery.

Indicates that a calibration certificate can be supplied for the product.

Manufacturer-recommended interval between periodic calibrations, where such an interval is specified.

Indicates that calibration can be performed in the installed location without factory return.

Indicates that an authorized user can execute a manufacturer-supported calibration procedure.

Indicates support for adjustment or calibration of measurement zero offset.

Indicates support for gain or span calibration using a reference measurement value.

Number of calibration points supported by the manufacturer-defined calibration procedure.

Indicates that access to calibration parameters or procedures is protected against unauthorized changes.

Indicates that the manufacturer provides a defined procedure or test facility for verifying measurement accuracy.

Indicates an internal self-test covering legally or technically relevant measurement functions.

Indicates storage of events relevant to metrological integrity, legal settings or protected measurement functions.

Indicates that changes to legally or metrologically relevant configuration parameters are recorded.

Indicates that metrologically relevant parameters are protected against unauthorized modification.

Indicates that legally or commercially relevant accumulated billing registers cannot be arbitrarily modified.

Compliance with IEC 62052-11 general requirements, tests and test conditions for electricity metering equipment.

Compliance with the European adoption of IEC 62052-11 for electricity metering equipment.

Compliance with IEC 62052-31 product safety requirements for electrical energy metering equipment.

Compliance with the European adoption of IEC 62052-31 metering-equipment safety requirements.

Compliance with IEC 62053-21 requirements applicable to static meters for active electrical energy.

Compliance with the European adoption of IEC 62053-21 for static active-energy meters.

Compliance with IEC 62053-22 requirements applicable to higher-accuracy static active-energy meters.

Compliance with the European adoption of IEC 62053-22.

Compliance with IEC 62053-23 requirements applicable to static reactive-energy meters.

Compliance with the European adoption of IEC 62053-23.

Compliance with IEC 62053-24 requirements applicable to static reactive-energy measurement at fundamental frequency.

Compliance with the European adoption of IEC 62053-24.

Compliance with IEC 62053-31 requirements applicable to pulse-output devices for electrical energy meters.

Compliance with the European adoption of IEC 62053-31 for meter pulse outputs.

Compliance with IEC 62056-21 requirements for local data exchange with electricity meters.

Compliance with the European adoption of IEC 62056-21.

Compliance with EN 50470-1 requirements applicable to electricity metering equipment.

Compliance with EN 50470-3 requirements applicable to static active-energy meters.

Compliance with OIML R 46 recommendations applicable to active electrical energy meters.

Compliance with IEC 61557-12 requirements for power metering and monitoring devices.

Compliance with the European adoption of IEC 61557-12 for power metering and monitoring devices.

Compliance with IEC 61000-4-30 power-quality measurement methods.

Compliance with the European adoption of IEC 61000-4-30 power-quality measurement methods.

Compliance with IEC 61000-4-7 requirements for harmonics and interharmonics measurement and instrumentation.

Compliance with the European adoption of IEC 61000-4-7.

Compliance with IEC 61000-4-15 functional and design requirements for flickermeters.

Compliance with the European adoption of IEC 61000-4-15.

Compliance with IEC 62586-1 product and performance requirements for power-quality instruments.

Compliance with IEC 62586-2 functional tests and uncertainty requirements for power-quality instruments.

Compliance with Directive 2014/35/EU where applicable to the product.

Compliance with Directive 2014/30/EU on electromagnetic compatibility where applicable.

Compliance with Directive 2014/53/EU where the product constitutes radio equipment.

Mass of the product together with its individual packaging and the accessories included in it.

External horizontal dimension of the product's individual package.

External vertical dimension of the product's individual package.

External depth dimension of the product's individual package.

Calculated or declared external volume of the product's individual package.

Design type of the product's individual or transport packaging.

Primary materials from which the product packaging is made.

Mass of the empty packaging without the product and its accessories.

Number of individual products contained in one packaging unit at the specified level.

Indicates whether the packaging used is declared recyclable as secondary raw material.

Indicates whether the packaging is designed for reuse without changing its primary purpose.

Indicates whether the packaging is intended to be returned to the supplier, manufacturer, or another participant in the logistics chain.