External horizontal dimension of the product between its outermost lateral points.

External vertical dimension of the product from its lowest to its highest point.

External distance between the foremost and rearmost surfaces of the product.

Mass of the product itself, excluding transport packaging, additional accessories, and external equipment.

Primary visually perceived colour of the product's external surface.

Primary material from which the product is manufactured.

Base electrically conductive material used for the current-carrying contacts of the connector or socket.

Surface plating or finish applied to the electrically mating connector contacts.

Primary structural or insulating material of the charging connector or socket housing.

Permissible spatial orientation of the component during installation and operation.

Installation arrangement permitted by the product design, such as wall-mounted, flush-mounted, floor-mounted, or another specified mounting type.

Method used to mechanically secure the product to a support, surface, or load-bearing structure.

Diameter of the hole provided for a fixing element used when mounting the product.

Voltage value assigned to the product by the manufacturer for specified application conditions and characteristics.

AC frequency assigned to the product for normal operating conditions.

Number of phases of the electrical system for which the product is designed to be connected or used.

Current assigned to the product by the manufacturer for the declared operating and thermal conditions.

Maximum nominal conductor cross-section permitted at the product's incoming connection.

Minimum conductor cross-section permitted for connection to the incoming terminal of the main power circuit.

Number of electrical socket outlets integrated into or supplied as part of the product.

Number of electrical connection points intended for incoming or supply-side connections.

Electrical connection technologies supported at the incoming or supply-side connection points of the product.

Minimum stripping length specified for an incoming or supply conductor.

Maximum stripping length specified for an incoming or supply conductor.

Manufacturer-declared tightening torque for an incoming or supply terminal.

Declared electrical contact resistance of a connection point where one common value applies to equivalent connections.

Rated voltage of the plug-in contact system declared by the manufacturer where specified separately from the rated voltage of the complete product.

EV conductive charging connector systems provided or supported by the product.

Indicates support for the EV charging Control Pilot conductor and signalling function.

Indicates support for the Proximity Pilot or equivalent proximity-detection conductor/function in the charging interface.

Indicates support for PWM signalling on the EV charging Control Pilot interface.

Total number of electrical contacts provided by the charging connector or socket interface.

Indicates that the Proximity Pilot circuit is used to encode or identify the allowable current capability of the charging cable assembly.

Manufacturer-declared resistance used by the applicable Proximity Pilot coding circuit.

Degree of enclosure protection against access to hazardous parts and ingress of solid objects and water, designated by the IP code.

Class of enclosure resistance to external mechanical impacts designated by the IK code.

Indicates that the EV charging connector or socket can be mechanically or electrically locked during a charging session.

Primary mechanism used to retain or lock the EV charging connector.

Indicates that temperature of the EV charging connector, contacts or socket is actively monitored.

Number of integrated temperature sensors used to monitor the charging connector, socket or current-carrying contact region.

Indicates whether the material and coating are designed to withstand ultraviolet radiation.

Indicates whether the product is designed for the combination of weather influences specified by the manufacturer.

Minimum ambient temperature at which normal operation of the product is permitted.

Maximum ambient temperature at which normal operation of the product is permitted.

Minimum ambient temperature permitted during storage of the product while not in operation.

Maximum ambient temperature permitted during storage of the product while not in operation.

Maximum relative air humidity permitted for the declared operating or test condition.

Declared number of mechanical operating cycles that the product can perform without electrical switching load.

Indicates whether mechanical or other physical coding can be used to prevent mating with an incompatible counterpart.

System, family, or designation of elements used for mechanical coding of the plug-in interface.

Indicates whether the mating connector can be mechanically locked to prevent unintended disconnection.

Mechanical method used to lock or retain the mating connector in the mated state.

Indicates whether a separate compatible mating connector is required to complete the electrical connection.

Indicates whether a compatible mating connector is supplied with the product.

Family, series, or designation of the plug-in interface of the compatible mating connector.

Manufacturer-declared number of mechanical mating and unmating cycles of the plug-in interface.

Mechanical force required to fully mate the compatible counterpart with the plug-in interface under the declared conditions.

Mechanical force required to fully withdraw the compatible counterpart from the plug-in interface under the declared conditions.

Indicates whether the specified protection against accidental contact with hazardous live parts is maintained when the mating connector is removed.

Indicates that the charging socket or connector incorporates protective shutters over live-contact openings.

Indicates that a protective cap or cover for the EV charging connector is supplied with the product.

Indicates whether the CE marking is applied to the product where applicable.

Compliance with Directive 2014/35/EU where applicable to the product.

Compliance with Directive 2014/30/EU on electromagnetic compatibility where applicable.

Compliance with IEC 62196-1 general requirements for EV plugs, socket-outlets, vehicle connectors, vehicle inlets and applicable cable assemblies.

Compliance with IEC 62196-2 dimensional compatibility requirements for AC EV charging accessories.

Mass of the product together with its individual packaging and the accessories included in it.

External horizontal dimension of the product's individual package.

External vertical dimension of the product's individual package.

External depth dimension of the product's individual package.

Calculated or declared external volume of the product's individual package.

Design type of the product's individual or transport packaging.

Primary materials from which the product packaging is made.

Mass of the empty packaging without the product and its accessories.

Number of individual products contained in one packaging unit at the specified level.

Indicates whether the packaging used is declared recyclable as secondary raw material.

Indicates whether the packaging is designed for reuse without changing its primary purpose.

Indicates whether the packaging is intended to be returned to the supplier, manufacturer, or another participant in the logistics chain.