Commercial or technical designation of a manufacturer's product family sharing a common design and compatible characteristics.

External horizontal dimension of the product between its outermost lateral points.

External vertical dimension of the product from its lowest to its highest point.

External distance between the foremost and rearmost surfaces of the product.

Transverse dimension of a product or its circular element measured through the centre between opposite points of the circumference.

Mass of the product itself, excluding transport packaging, additional accessories, and external equipment.

Diameter of the hole provided for a fixing element used when mounting the product.

Horizontal dimension of the mounting cutout or opening required to install the product in a prepared surface or recess.

Vertical dimension of the mounting cutout or opening required to install the product in a prepared surface or recess.

Minimum mounting-panel thickness accepted by the product mounting system.

Maximum mounting-panel thickness accepted by the product mounting system.

Maximum distance that the installed product projects forward from the finished mounting-panel surface.

Required depth behind the mounting-panel surface for the installed product, excluding external conductor bend allowance unless otherwise stated.

Maximum external diameter of the visible front bezel or mounting ring where the panel-mounted product has a circular front geometry.

Primary material from which the product is manufactured.

Primary visually perceived colour of the product's external surface.

Installation arrangement permitted by the product design, such as wall-mounted, flush-mounted, floor-mounted, or another specified mounting type.

Method used to mechanically secure the product to a support, surface, or load-bearing structure.

Permissible spatial orientation of the component during installation and operation.

Mechanical method used to secure the product to the mounting panel after insertion through the panel opening.

Indicates that the panel opening requires an additional notch, flat or equivalent feature to prevent rotation of the installed product.

Indicates that a gasket or sealing element used between the product and mounting panel is supplied with the product.

Indicates that the retaining or fixing ring required for mounting the product in the panel is supplied.

Indicates that a threaded fixing nut required for panel installation is supplied with the product.

Indicates that the general fixing hardware required for the declared installation method is supplied with the product.

Operating-circuit voltage with reference to which the product's performance characteristics are specified.

Voltage with reference to which the product's insulation clearances and dielectric properties are specified.

Peak value of an impulse voltage of specified waveform that the product insulation must withstand without breakdown.

Type of electrical current for which the product's main supply circuit is intended.

Voltage value assigned to the product by the manufacturer for specified application conditions and characteristics.

AC frequency assigned to the product for normal operating conditions.

Minimum operating voltage of the integrated electrical visual indicator.

Maximum operating voltage of the integrated electrical visual indicator.

Minimum operating current of the integrated electrical visual indicator.

Maximum operating current of the integrated electrical visual indicator.

Type of electrical current for which the integrated visual indicator is designed.

Electrical power consumed by the product itself in the declared normal operating mode.

Maximum manufacturer-declared current drawn from the electrical supply during normal operation.

Total number of electrical connection points provided by the product.

Conductor connection technology used specifically for the control-circuit terminals.

Minimum conductor cross-section accepted by the control-circuit terminal.

Maximum conductor cross-section accepted by the control-circuit terminal.

Manufacturer-declared tightening torque specifically for a screw-type control-circuit terminal.

Degree of enclosure protection against access to hazardous parts and ingress of solid objects and water, designated by the IP code.

Ingress protection rating applicable specifically to the installed front face of the product.

Ingress protection rating applicable specifically to the rear portion of the installed product.

Class of enclosure resistance to external mechanical impacts designated by the IK code.

Indicates whether the design prevents finger access to hazardous live parts in the intended condition.

Indicates whether the design provides protection against accidental contact with hazardous live parts.

Category characterizing the expected level of impulse overvoltages at the product's point of use.

Minimum ambient temperature at which normal operation of the product is permitted.

Maximum ambient temperature at which normal operation of the product is permitted.

Minimum ambient temperature permitted during storage of the product while not in operation.

Maximum ambient temperature permitted during storage of the product while not in operation.

Maximum relative air humidity permitted for the declared operating or test condition.

Maximum altitude above sea level at which the product may be installed without exceeding the declared conditions.

Amplitude or test-method-specified acceleration of vibration applied during product testing.

Maximum acceleration generated during mechanical shock testing of the product.

Indicates whether the material and coating are designed to withstand ultraviolet radiation.

Duration of salt-spray testing withstood by the product or coating under the declared conditions.

Groups of chemicals or environments whose effects the product can withstand under the declared conditions.

Degree of pollution of the surrounding microenvironment considered when selecting insulation distances and product characteristics.

Physical product configuration supplied under the catalog number, such as a complete assembled device or a modular operator component.

Indicates that a separate external legend, identification or marking plate is supplied with the product.

Indicates that the external legend or identification plate can be replaced independently.

Indicates whether insulating terminal covers or protective terminal shrouds are supplied with the product.

Indicates that electrical connection terminals are individually identified by manufacturer-applied markings.

Color of the integrated visual status indicator or LED.

Primary light-generation technology used by the visual indicator or signaling device.

Indicates whether the light-generating element can be replaced according to the manufacturer instructions.

Manufacturer-declared operating lifetime of the light source under specified conditions.

Physical color or tint of the optical lens or diffuser.

Primary material used for the optical lens, diffuser or light cover.

Manufacturer-declared luminous intensity of the visual signaling output.

Manufacturer-declared total luminous flux of the visual signaling output.

Manufacturer-declared angular range over which the visual indication remains observable.

Colors that can be generated by a multicolor or configurable visual signaling device.

Number of independently identifiable visual indication channels provided by the product.

Physical arrangement of visual indication elements on the front face of the product.

Number of separate visible indication windows, lenses or front-panel indication fields.

Indicates that the front panel provides a dedicated field for identifying the corresponding channel, phase or function.

Visual signaling modes supported by the device.

Minimum manufacturer-declared flashing or pulsing frequency.

Maximum manufacturer-declared flashing or pulsing frequency.

Number of selectable or predefined visual signaling patterns.

Indicates that the brightness of the visual signaling output can be adjusted.

Number of selectable brightness levels where stepped brightness control is provided.

Indicates that one optical signaling element can generate more than one signal color.

Indicates that the product provides a function for testing its visual indicators.

Certification, market-approval, or conformity marks applicable to the product.

Indicates whether the CE marking is applied to the product where applicable.

Indicates whether product compliance with applicable RoHS restrictions on hazardous substances has been declared.

Indicates whether the manufacturer declares compliance of the product with applicable REACH Regulation requirements.

Indicates whether documentation is included in the product's standard supply.

Types of technical documentation supplied with or explicitly included for the product.

Compliance with applicable IEC 60947-5-1 requirements for control-circuit devices and switching elements.

Mass of the product together with its individual packaging and the accessories included in it.

External horizontal dimension of the product's individual package.

External vertical dimension of the product's individual package.

External depth dimension of the product's individual package.

Calculated or declared external volume of the product's individual package.

Design type of the product's individual or transport packaging.

Primary materials from which the product packaging is made.

Mass of the empty packaging without the product and its accessories.

Number of individual products contained in one packaging unit at the specified level.

Indicates whether the packaging used is declared recyclable as secondary raw material.

Indicates whether the packaging is designed for reuse without changing its primary purpose.

Indicates whether the packaging is intended to be returned to the supplier, manufacturer, or another participant in the logistics chain.

Country of origin of the goods declared for customs or commercial purposes.

Commodity code under the international Harmonized Commodity Description and Coding System.