Commercial or technical designation of a manufacturer's product family sharing a common design and compatible characteristics.

Range of tasks and systems for which the manufacturer recommends the component.

Primary function of the device and its intended use as defined by its design and the manufacturer's documentation.

External horizontal dimension of the product between its outermost lateral points.

External vertical dimension of the product from its lowest to its highest point.

Indicates manufacturer-declared resistance to repeated or specified torsional mechanical loading.

Indicates whether the product materials retain their declared properties when exposed to ozone.

Primary optical propagation type of the fibres contained in the cable.

Manufacturer-declared standardized optical fibre category such as OS1, OS2 or OM1 to OM5.

Applicable ITU-T optical fibre recommendation declared for the fibres in the cable.

External linear dimension of the product along its longitudinal direction or principal length axis.

Transverse dimension of a product or its circular element measured through the centre between opposite points of the circumference.

Mass of the product itself, excluding transport packaging, additional accessories, and external equipment.

Manufacturer-declared product mass per unit length.

Nominal thickness of the external protective cable sheath.

Nominal diameter of an individual armour wire where wire armour is used.

Nominal thickness of the armour layer or armour element where applicable.

Nominal diameter of the optical fibre core.

Nominal outside diameter of the optical cladding.

Nominal outside diameter of the primary coated optical fibre.

Manufacturer-declared mode field diameter for applicable single-mode optical fibre.

Total number of optical fibres contained in the finished cable.

Number of loose tubes, micro-modules or equivalent fibre-containing tubular elements.

Nominal number of optical fibres contained in one tube or micro-module.

Number of optical fibre ribbons contained in the cable.

Number of optical fibres contained in one fibre ribbon.

Primary material of the outer protective sheath or jacket of a cable.

Color of the distinct outer sheath or jacket.

Indicates that the insulated conductor has a distinct outer sheath or jacket in addition to its primary electrical insulation.

Indicates that filler material is used between cable cores to form or stabilize the cable construction.

Primary material used as filler between cable cores.

Indicates that a ripcord or tear cord is incorporated beneath the cable sheath to assist sheath removal.

Primary material used for the cable ripcord or tear cord.

Primary metallic material used for the cable armour.

Primary material or technology used to provide longitudinal water blocking within the cable construction.

Mechanical buffering or fibre organization construction used inside the optical cable.

Material of the central mechanical strength member.

Manufacturer-declared fibre or tube colour coding standard.

Permissible installation location of the product: indoors, outdoors, in a technical area, or as part of equipment.

Indicates the ability of the product to bend or change shape within its design limits without loss of normal function.

Minimum bend radius declared by the manufacturer at which installation or operation of the product is permitted without unacceptable damage.

Minimum manufacturer-declared bend radius for repeated dynamic flexing under the specified operating conditions.

Maximum manufacturer-declared pulling or installation force that may be applied to the product without mechanical damage.

Indicates that the cable is manufacturer-declared as suitable for direct burial in soil without an additional continuous cable duct or conduit.

Manufacturer-declared or standardized installation and routing methods for which the cable is suitable. This describes how the cable itself may be laid or routed and is distinct from mounting_type used for mounting standalone products.

Manufacturer-declared numerical aperture of the optical fibre where applicable.

Common operating wavelengths for which the optical fibre cable is manufacturer-declared.

Maximum manufacturer-declared optical attenuation at 850 nm.

Maximum manufacturer-declared optical attenuation at 1300 nm.

Maximum manufacturer-declared optical attenuation at 1310 nm.

Maximum manufacturer-declared optical attenuation at 1550 nm.

Maximum manufacturer-declared optical attenuation at 1625 nm.

Minimum manufacturer-declared overfilled-launch modal bandwidth at 850 nm.

Minimum manufacturer-declared overfilled-launch modal bandwidth at 1300 nm.

Minimum manufacturer-declared effective modal bandwidth at 850 nm.

Maximum manufacturer-declared chromatic dispersion at 1550 nm.

Maximum manufacturer-declared polarization mode dispersion coefficient.

Indicates that the cable incorporates a mechanical armour layer.

Mechanical construction of the cable armour layer.

Indicates that the cable construction includes barriers intended to limit longitudinal water propagation along the cable.

Indicates manufacturer-declared compliance with the applicable longitudinal water-penetration test for the cable construction.

Indicates that the cable incorporates a continuous construction layer intended to limit radial water ingress through the cable covering.

Construction type of the radial moisture or water barrier incorporated in the cable.

Indicates that the cable outer construction is designed or qualified for enhanced abrasion resistance.

Indicates manufacturer-declared resistance to mechanical crushing or compressive loading under the applicable test conditions.

Indicates whether the product material is classified as halogen-free according to the characteristics declared by the manufacturer.

Indicates the manufacturer-declared ability of a material or product to limit the spread of combustion under specified test conditions.

Indicates manufacturer-declared low-smoke performance of the cable materials.

Manufacturer-declared limiting oxygen index of the applicable insulation, sheath or complete product material system.

Minimum manufacturer-declared light transmittance measured during the applicable smoke-density test.

Maximum manufacturer-declared halogen acid gas content determined for the applicable cable material or product construction.

Minimum manufacturer-declared pH value of the aqueous solution obtained from gases evolved during combustion.

Maximum manufacturer-declared conductivity measured for the aqueous solution obtained from gases evolved during combustion.

Maximum manufacturer-declared short-term tensile load for the optical fibre cable.

Maximum manufacturer-declared long-term tensile load for the optical fibre cable.

Manufacturer-declared crush load or crush resistance value for the optical fibre cable.

Environmental conditions under which installation and operation of the product are permitted.

Indicates manufacturer-declared resistance to water exposure under the applicable product or test conditions.

Indicates whether the product is designed for the combination of weather influences specified by the manufacturer.

Indicates whether the material and coating are designed to withstand ultraviolet radiation.

Duration of accelerated or natural weathering testing of the product.

Indicates whether the product materials retain their declared properties when exposed to the specified oils.

Groups of chemicals or environments whose effects the product can withstand under the declared conditions.

Indicates whether the product's resistance to solar radiation has been verified.

Maximum solar radiation flux density permitted under the declared operating conditions.

Minimum ambient temperature at which normal operation of the product is permitted.

Maximum ambient temperature at which normal operation of the product is permitted.

Minimum ambient temperature permitted during storage of the product while not in operation.

Maximum ambient temperature permitted during storage of the product while not in operation.

Minimum ambient temperature at which the manufacturer permits installation of the product.

Maximum ambient temperature at which the manufacturer permits installation of the product.

Maximum relative air humidity permitted for the declared operating or test condition.

Indicates that the optical cable includes a central mechanical strength member.

Indicates that aramid yarn is used as a tensile strength member.

Indicates use of manufacturer-declared bend-insensitive optical fibre.

Compliance with IEC 60332-1-2 vertical flame propagation test requirements applicable to a single insulated wire or cable.

Compliance with applicable IEC 60754-1 requirements for determination of halogen acid gas content from cable materials.

Compliance with applicable IEC 60754-2 requirements for determination of acidity and conductivity of gases evolved during combustion.

Compliance with applicable IEC 61034-2 smoke-density test requirements for burning cables or wires.

Manufacturer-declared reaction-to-fire class for electric cables or wires under the applicable CPR classification system.

Manufacturer-declared supplementary CPR smoke-production classification.

Manufacturer-declared supplementary CPR classification for flaming droplets or particles.

Manufacturer-declared supplementary CPR acidity classification based on combustion-gas pH and conductivity.

Manufacturer-declared or test-reported vertical flame spread height used in the applicable reaction-to-fire assessment.

Test-reported total heat release over 1200 seconds where declared for CPR reaction-to-fire classification.

Test-reported peak heat release rate where declared for CPR reaction-to-fire classification.

Fire growth rate index reported for the applicable CPR reaction-to-fire test.

Test-reported total smoke production over 1200 seconds where declared for CPR classification.

Test-reported peak smoke production rate where declared for CPR classification.

Manufacturer-declared compliance with EN 50575 where the wire or cable is placed on the market for permanent incorporation in construction works and the standard is applicable.

Certification, market-approval, or conformity marks applicable to the product.

Indicates whether the CE marking is applied to the product where applicable.

Indicates whether product compliance with applicable RoHS restrictions on hazardous substances has been declared.

Indicates whether the manufacturer declares compliance of the product with applicable REACH Regulation requirements.

Manufacturer-declared compliance with IEC 60794-1-1 generic requirements for optical fibre cables.

Applicable sectional or family part of IEC 60794 explicitly declared for the optical cable.

Manufacturer-declared compliance of the contained optical fibres with the applicable IEC 60793 requirements.

Applicable IEC 60793 part explicitly declared for the optical fibre type.

Mass of the product together with its individual packaging and the accessories included in it.

External horizontal dimension of the product's individual package.

External vertical dimension of the product's individual package.

External depth dimension of the product's individual package.

Calculated or declared external volume of the product's individual package.

Design type of the product's individual or transport packaging.

Primary materials from which the product packaging is made.

Mass of the empty packaging without the product and its accessories.

Number of individual products contained in one packaging unit at the specified level.

Indicates whether the packaging used is declared recyclable as secondary raw material.

Indicates whether the packaging is designed for reuse without changing its primary purpose.

Indicates whether the packaging is intended to be returned to the supplier, manufacturer, or another participant in the logistics chain.

Country of origin of the goods declared for customs or commercial purposes.

Commodity code under the international Harmonized Commodity Description and Coding System.