Sine-Wave Filter
Drive-output LC filter intended to convert PWM voltage into a waveform close to sinusoidal.
A sine-wave filter is installed between a PWM drive and an electric motor and is used to strongly suppress high-frequency components of the output voltage.
Unlike a conventional dV/dt filter, its purpose is to achieve much deeper reconstruction of a near-sinusoidal voltage waveform and to reduce high-frequency motor current.
Key parameters include inductance, maximum permitted output frequency, dV/dt limitation, percentage impedance, voltage drop, and power losses.
Selection must take into account motor current, drive switching frequency, fundamental output frequency, and the operating limits specified by the filter manufacturer.
An incorrect combination of frequency and filter parameters can cause resonance, overheating, or excessive voltage drop.
Sine-wave filters for VFD motor outputs, long cables, and motors sensitive to PWM waveforms.
Sine-Wave Filter
General3
Commercial or technical designation of a manufacturer's product family sharing a common design and compatible characteristics.
Range of tasks and systems for which the manufacturer recommends the component.
Primary function of the device and its intended use as defined by its design and the manufacturer's documentation.
Dimensions6
External horizontal dimension of the product between its outermost lateral points.
External vertical dimension of the product from its lowest to its highest point.
External distance between the foremost and rearmost surfaces of the product.
External linear dimension of the product along its longitudinal direction or principal length axis.
Transverse dimension of a product or its circular element measured through the centre between opposite points of the circumference.
Mass of the product itself, excluding transport packaging, additional accessories, and external equipment.
Mounting and Installation8
Method used to mechanically secure the product to a support, surface, or load-bearing structure.
Installation arrangement permitted by the product design, such as wall-mounted, flush-mounted, floor-mounted, or another specified mounting type.
Permissible spatial orientation of the component during installation and operation.
Indicates whether the design provides for mounting equipment on a DIN rail.
Number of holes provided in the product for mechanical fixing.
Diameter of the hole provided for a fixing element used when mounting the product.
Distance between the centres of mounting holes in the horizontal direction.
Distance between the centres of mounting holes in the vertical direction.
Electrical Parameters11
Voltage value assigned to the product by the manufacturer for specified application conditions and characteristics.
Nominal inductance of a reactor, choke, filter or winding.
Maximum fundamental motor/output frequency permitted for the sine-wave filter.
Current assigned to the product by the manufacturer for the declared operating and thermal conditions.
Rated impedance expressed as a percentage at the specified current and frequency.
Maximum voltage slew rate at the filtered output under declared conditions.
Rated active electrical power of the product declared by the manufacturer for specified operating conditions.
Voltage drop across the component at the stated operating point, expressed as a percentage.
AC frequency assigned to the product for normal operating conditions.
Manufacturer-declared power dissipation/loss at the stated load condition.
Electrical power consumed by the product itself in the declared normal operating mode.
Environmental Conditions10
Degree of enclosure protection against access to hazardous parts and ingress of solid objects and water, designated by the IP code.
Class of enclosure resistance to external mechanical impacts designated by the IK code.
Minimum ambient temperature at which normal operation of the product is permitted.
Maximum ambient temperature at which normal operation of the product is permitted.
Minimum ambient temperature permitted during storage of the product while not in operation.
Maximum ambient temperature permitted during storage of the product while not in operation.
Minimum relative air humidity permitted for the declared operating or test condition.
Maximum relative air humidity permitted for the declared operating or test condition.
Indicates whether the product's resistance to vibration has been verified under the declared conditions.
Indicates whether the product's resistance to short-duration mechanical shocks has been verified.
Standards and Compliance7
Indicates whether the CE marking is applied to the product where applicable.
Indicates whether product compliance with applicable RoHS restrictions on hazardous substances has been declared.
Indicates whether the manufacturer declares product compliance with IEC 60529.
Indicates whether the product has been tested according to applicable methods of the IEC 60068 series.
Compliance with applicable IEC 61800-3 EMC requirements for adjustable-speed electrical power drive systems.
Compliance with applicable IEC 61000-6-2 generic immunity requirements for industrial environments.
Compliance with applicable IEC 61000-6-4 generic emission requirements for industrial environments.